DataSheet.es    


PDF DS21Q348 Data sheet ( Hoja de datos )

Número de pieza DS21Q348
Descripción 3.3V E1/T1/J1 Line Interface
Fabricantes Dallas Semiconducotr 
Logotipo Dallas Semiconducotr Logotipo



Hay una vista previa y un enlace de descarga de DS21Q348 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! DS21Q348 Hoja de datos, Descripción, Manual

www.maxim-ic.com
FEATURES
§ Complete E1, T1, or J1 line interface unit
(LIU)
§ Supports both long-haul and short-haul
trunks
§ Internal software-selectable receive-side
termination for 75/100/120W
§ 3.3V power supply
§ 32-bit or 128-bit crystal-less jitter attenuator
requires only a 2.048MHz master clock for
both E1 and T1 with option to use 1.544MHz
for T1
§ Generates the appropriate line build-outs,
with and without return loss, for E1 and
DSX-1 and CSU line build-outs for T1
§ AMI, HDB3, and B8ZS, encoding/decoding
§ 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output synthesized to
recovered clock
§ Programmable monitor mode for receiver
§ Loopbacks and PRBS pattern generation/
detection with output for received errors
§ Generates/detects in-band loop codes, 1 to 16
bits including CSU loop codes
§ 8-bit parallel or serial interface with optional
hardware mode
§ Muxed and nonmuxed parallel bus supports
Intel or Motorola
§ Detects/generates blue (AIS) alarms
§ NRZ/bipolar interface for TX/RX data I/O
§ Transmit open-circuit detection
§ Receive Carrier Loss (RCL) indication
(G.775)
§ High-Z State for TTIP and TRING
§ 50mA (rms) current limiter
DS21348/Q348
3.3V E1/T1/J1 Line Interface
PIN DESCRIPTION
44
1
44 TQFP
7 mm
CABGA
ORDERING INFORMATION
DS21348TN 44-Pin TQFP (-40°C to +85°C)
DS21348T 44-Pin TQFP (0o C to +70oC)
DS21348GN 7mm CABGA (-40°C to +85°C)
DS21348G 7mm CABGA (0o C to +70oC)
DS21Q348N (Quad) BGA (-40°C to +85°C)
DS21Q348 (Quad) BGA (0o C to +70o C)
1 of 73
111501

1 page




DS21Q348 pdf
2. LIST OF TABLES
DS21348/Q348
Table 4-1 BUS INTERFACE SELECTION ................................................................................................ 9
Table 4-2a PIN ASSIGNMENT IN PARALLEL PORT MODE .............................................................. 10
Table 4-2b PIN DESCRIPTIONS IN PARALLEL PORT MODE (Sorted by Pin Name, DS21348T Pin
Numbering) .......................................................................................................................................... 11
Table 4-3a PIN ASSIGNMENT IN SERIAL PORT MODE..................................................................... 13
Table 4-3b PIN DESCRIPTIONS IN SERIAL PORT MODE (Sorted by Pin Name, DS21348T Pin
Numbering) .......................................................................................................................................... 14
Table 4-4a PIN ASSIGNMENT IN HARDWARE MODE....................................................................... 16
Table 4-4b PIN DESCRIPTIONS IN HARDWARE MODE (Sorted by Pin Name, DS21348T Pin
Numbering) .......................................................................................................................................... 17
Table 4-5 LOOPBACK CONTROL IN HARDWARE MODE ................................................................ 20
Table 4-6 TRANSMIT DATA CONTROL IN HARDWARE MODE ..................................................... 20
Table 4-7 RECEIVE SENSITIVITY SETTINGS...................................................................................... 20
Table 4-8 MONITOR GAIN SETTINGS .................................................................................................. 20
Table 4-9 INTERNAL RX TERMINATION SELECT ............................................................................. 20
Table 4-10 MCLK SELECTION................................................................................................................ 20
Table 5-1 REGISTER MAP ....................................................................................................................... 23
Table 6-1 MCLK SELECTION.................................................................................................................. 29
Table 6-2 RECEIVE SENSITIVITY SETTINGS...................................................................................... 31
Table 6-3 BACK PLANE CLOCK SELECT............................................................................................. 32
Table 6-4 MONITOR GAIN SETTINGS .................................................................................................. 32
Table 6-5 INTERNAL RX TERMINATION SELECT ............................................................................. 33
Table 7-1 RECEIVED ALARM CRITERIA ............................................................................................. 35
Table 7-2 RECEIVE LEVEL INDICATION............................................................................................. 38
Table 8-1 TRANSMIT CODE LENGTH................................................................................................... 40
Table 8-2 RECEIVE CODE LENGTH ...................................................................................................... 40
Table 8-3 DEFINITION OF RECEIVED ERRORS.................................................................................. 44
Table 8-4 FUNCTION OF ECRS BITS AND RNEG PIN ........................................................................ 45
Table 9-1 LINE BUILD OUT SELECT FOR E1 IN REGISTER CCR4 (ETS = 0) ................................. 48
Table 9-2 LINE BUILD OUT SELECT FOR T1 IN REGISTER CCR4 (ETS = 1) ................................. 48
Table 9-3 TRANSFORMER SPECIFICATIONS FOR 3.3V OPERATION ............................................ 48
Table 10-1 DS21Q348 PIN ASSIGNMENT.............................................................................................. 55
5 of 73

5 Page





DS21Q348 arduino
DS21348/Q348
PIN DESCRIPTIONS IN PARALLEL PORT MODE (Sorted by Pin Name,
DS21348T Pin Numbering) Table 4-2b
ACRONYM PIN I/O DESCRIPTION
A0 to A4
ALE(AS)
11
to
7
4
BIS0/BIS1
BPCLK
32/33
31
CS*
D0 / AD0
to
D7 / AD7
HRST*
INT*
MCLK
1
19
to
12
29
23
30
NA
PBEO
-
24
PBTS
44
I Address Bus. In nonmultiplexed bus operation (BIS1 = 0, BIS0 =
1), serves as the address bus. In multiplexed bus operation (BIS1 =
0, BIS0 = 0), these pins are not used and should be tied low.
I Address Latch Enable (Address Strobe). When using the parallel
port (BIS1 = 0) in multiplexed bus mode (BIS0 = 0), serves to
demultiplex the bus on a positive-going edge. In nonmultiplexed bus
mode (BIS0 = 1), should be tied low.
I Bus Interface Select Bits 0 & 1. Used to select bus interface option.
See Table 4-1 for details.
O Back Plane Clock. A 16.384MHz, 8.192MHz, 4.096MHz, or
2.048MHz clock output that is referenced to RCLK selectable via
CCR5.7 and CCR5.6. In hardware mode, defaults to 16.384MHz
output.
I Chip Select. Must be low to read or write to the device. CS* is an
active low signal.
I/O Data Bus/Address/Data Bus. In nonmultiplexed bus operation
(BIS1 = 0, BIS0 = 1), serves as the data bus. In multiplexed bus
operation (BIS1 = 0, BIS0 = 0), serves as an 8-bit multiplexed
address/data bus.
I Hardware Reset. Bringing HRST* low will reset the DS21348
setting all control bits to their default state of all zeros.
O Interrupt [INT*] Pin 23. Flags host controller during conditions
and change of conditions defined in the Status Register. Active low,
open drain output.
I Master Clock. A 2.048MHz (±50ppm) clock source with TTL
levels is applied at this pin. This clock is used internally for both
clock/data recovery and for jitter attenuation. Use of a T1 1.544
MHz clock source is optional.
See Note 2.
I Not Assigned. Should be tied low.
O PRBS Bit Error Output. The receiver will constantly search for a
215-1 or a 220-1 PRBS depending on the ETS bit setting (CCR1.7).
Remains high if out of synchronization with the PRBS pattern. Goes
low when synchronized to the PRBS pattern. Any errors in the
received pattern after synchronization will cause a positive going
pulse (with same period as E1 or T1 clock) synchronous with
RCLK. PRBS bit errors can also be reported to the ECR1 and ECR2
registers by setting CCR6.2 to a logic 1.
I Parallel Bus Type Select. When using the parallel port (BIS1 = 0),
set high to select Motorola bus timing, set low to select Intel bus
timing. This pin controls the function of the RD*(DS*), ALE(AS),
and WR*(R/W*) pins. If PBTS = 1 and BIS1 = 0, then these pins
assume the Motorola function listed in parenthesis (). In serial port
mode, this pin should be tied low.
11 of 73

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet DS21Q348.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
DS21Q3483.3V E1/T1/J1 Line InterfaceDallas Semiconducotr
Dallas Semiconducotr
DS21Q348N3.3V E1/T1/J1 Line InterfaceDallas Semiconducotr
Dallas Semiconducotr

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar