|
|
PDF FEP16GT Data sheet ( Hoja de datos )
| Número de pieza | FEP16GT | |
| Descripción | FAST EFFICIENT PLASTIC RECTIFIER | |
| Fabricantes | General Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de FEP16GT (archivo pdf) en la parte inferior de esta página. Total 2 Páginas | ||
|
No Preview Available !
FEP16AT THRU FEP16JT
FAST EFFICIENT PLASTIC RECTIFIER
Reverse Voltage - 50 to 600 Volts Forward Current - 16.0 Amperes
TO-220AB
0.160 (4.06)
0.140 (3.56)
0.415 (10.54) MAX.
0.370 (9.40)
0.360 (9.14)
0.154 (3.91)
0.148 (3.74)DIA.
0.113 (2.87)
0.103 (2.62)
0.145 (3.68)
0.135 (3.43)
0.410 (10.41)
0.390 (9.91)
PIN
1 23
0.635 (16.13)
0.625 (15.87)
0.350 (8.89)
0.330 (8.38)
1.148 (29.16)
1.118 (28.40)
0.560 (14.22)
0.530 (13.46)
0.105 (2.67)
0.095 (2.41)
0.037 (0.94)
0.027 (0.68)
0.105 (2.67)
0.095 (2.41)
0.205 (5.20)
0.195 (4.95)
0.022 (0.56)
0.014 (0.35)
PIN 1
PIN 3
Dimensions are in inches and (millimeters)
0.185 (4.70)
0.175 (4.44)
0.055 (1.39)
0.045 (1.14)
0.560 (14.22)
0.530 (13.46)
0.110 (2.79)
0.100 (2.54)
PIN 2
CASE
FEATURES
♦ Plastic package has Underwriters Laboratory
Flammability Classification 94V-0
♦ Dual rectifier construction, positive centertap
♦ Glass passivated chip junctions
♦ Low power loss
♦ Low forward voltage, high current capability
♦ High surge current capability
♦ Superfast recovery times for high efficiency
♦ High temperature soldering guaranteed:
250°C, 0.16" (4.06mm) from case for 10 seconds
MECHANICAL DATA
Case: JEDEC TO-220AB molded plastic body over
passivated chips
Terminals: Plated leads solderable per MIL-STD-750,
Method 2026
Polarity: As marked
Mounting Position: Any
Mounting Torque: 5 in. - lbs. max.
Weight: 0.08 ounce, 2.24 grams
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25°C ambient temperature unless otherwise specified.
FEP FEP FEP FEP FEP FEP FEP FEP
SYMBOLS 16AT 16BT 16CT 16DT 16FT 16GT 16HT 16JT UNITS
Maximum repetitive peak reverse voltage
Maximum RMS voltage
Maximum DC blocking voltage
Maximum average forward rectified current
at TC=100°C
Peak forward surge current
8.3ms single half sine-wave superimposed
on rated load (JEDEC Method)
VRRM 50 100 150 200 300 400 500 600 Volts
VRMS 35 70 105 140 210 280 350 420 Volts
VDC 50 100 150 200 300 400 500 600 Volts
I(AV) 16.0 Amps
IFSM
200.0
Amps
Maximum instantaneous forward voltage per leg
at 8.0A
VF
0.95 1.3 1.5 Volts
Maximum DC reverse current
at rated DC blocking voltage per leg
Maximum reverse recovery time (NOTE 1)
per leg
TC=25°C
TC=100°C
IR
trr
10.0
500.0
35.0
50.0
µA
ns
Typical Junction Capacitance per leg (NOTE 2)
Typical thermal resistance (NOTE 3)
Operating junction and storage temperature range
CJ
RΘJA
RΘJC
TJ, TSTG
85.0
15.0
2.2
-55 to +150
60.0 pF
°C/W
°C
NOTES:
(1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A
(2) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts
(3) Thermal resistance from junction to ambient and from junction to case per leg mounted on heatsink
4/98
1 page | ||
| Páginas | Total 2 Páginas | |
| PDF Descargar | [ Datasheet FEP16GT.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| FEP16GT | FAST EFFICIENT PLASTIC RECTIFIER | General Semiconductor |
| FEP16GT | 16 Ampere Heatsink Common Cathode Fast Recovery Half Bridge Rectifiers |  Thinki Semiconductor |
| FEP16GT | Dual Common Cathode Ultrafast Plastic Rectifier |  Vishay |
| FEP16GT | (FEP16AT - FEP16JT) Ultrafast Plastic Rectifiers |  EIC |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |