DataSheet.es    


PDF M-8888-01 Data sheet ( Hoja de datos )

Número de pieza M-8888-01
Descripción DTMF Transceiver
Fabricantes Clare Inc. 
Logotipo Clare  Inc. Logotipo



Hay una vista previa y un enlace de descarga de M-8888-01 (archivo pdf) en la parte inferior de esta página.


Total 14 Páginas

No Preview Available ! M-8888-01 Hoja de datos, Descripción, Manual

Features
· Advanced CMOS technology for low power con-
sumption and increased noise immunity
· Complete DTMF transmitter/receiver in a single
chip
Standard 8051, 8086/8 microprocessor port
· Central office quality and performance
· Adjustable guard time
· Automatic tone burst mode
· Call progress mode
· Single +5 Volt power supply
· 20-pin DIP and SOIC packages
· 2 MHz microprocessor port operation
·· Inexpensive 3.58 MHz crystal
Applications
Paging systems
· Repeater systems/mobile radio
· Interconnect dialers
· PBX systems
· Computer systems
· Fax machines
· Pay telephone
·· Credit card verification
M-8888
DTMF Transceiver
Description
The M-8888 is a complete DTMF Transmitter
Receiver that features adjustable guard time, auto-
matic tone burst mode, call progress mode, and a fully
compatible 8051, 8086/8 microprocessor interface.
The receiver portion is based on the industry standard
M-8870 DTMF Receiver, while the transmitter uses a
switched-capacitor digital-to-analog converter for low-
distortion, highly accurate DTMF signaling. Tone
bursts can be transmitted with precise timing by mak-
ing use of the automatic tone burst mode. To analyze
call progress tones, a call progress filter can be select-
ed by an external microprocessor.
Ordering Information
Part #
Description
M-8888-01P
20-pin plastic DIP
M-8888-01SM 20-pin plastic SOIC
M-8888-01T
20-pin plastic SOIC,Tape and Reel
Pin Connections
Block Diagram
DS-M8888-R1
www.clare.com
1

1 page




M-8888-01 pdf
M-8888
The divider output clocks another counter that
addresses the sinewave lookup ROM. The lookup
table contains codes used by the switched capacitor
D/A converter to obtain discrete and highly accurate
DC voltage levels. Two identical circuits are used to
produce row and column tones, which are then mixed
using a low-noise summing amplifier. The oscillator
described needs no startup time as in other DTMF
generators, since the crystal oscillator is running con-
tinuously, thus providing a high degree of tone burst
accuracy. When there is no tone output signal, the
TONE pin assumes a DC level of 2.5 volts (typically).
A bandwidth limiting filter is incorporated to attenuate
distortion products above 4 KHz.
Burst Mode:
Certain telephony applications require that generated
DTMF signals be of a specific duration, determined
Actual Frequencies vs Standard Requirements
Active Cell
L1
L2
L3
L4
H1
H2
H3
H4
Output Frequency(Hz)
Specified
Actual
697 699.1
770 766.2
852 847.4
941 948.0
1209
1215.9
1336
1331.7
1447
1471.9
1633
1645.0
% Error
+ 0.30
- 0.49
- 0.54
+ 0.74
+ 0.57
- 0.32
- 0.35
+ 0.73
Control Register A Description
either by the application or by any of the existing
exchange transmitter specifications. Standard DTMF
signal timing can be accomplished by making use of
the burst mode. The transmitter is capable of issuing
symmetric bursts/pauses of predetermined duration.
This burst/pause duration is 51 ms ± 1 ms, a standard
interval for autodialer and central office applications.
After the burst/pause has been issued, the appropriate
bit is set in the status register, indicating that the trans-
mitter is ready for more data.
The timing described in the previous paragraph is
available when the DTMF mode has been selected.
However, when call progress (CP) mode is selected, a
secondary burst/pause time is available that extends
this interval to 102 ms ± 2 ms. The extended interval is
useful when precise tone bursts of longer than 51 ms
duration and 51 ms pause are desired. Note that when
CP mode and burst mode have been selected, DTMF
tones may be transmitted only and not received. In
applications where a nonstandard burst/pause time is
desirable, a software timing loop or external timer can
be used to provide the timing pulses when the burst
mode is disabled by enabling and disabling the trans-
mitter.
The M-8888 is initialized on powerup sequence with
DTMF mode and burst mode selected.
Single-Tone Generation:
A single-tone mode is available whereby individual
tones from the low group or high group can be gener-
ated. This mode can be used for DTMF test equipment
applications, acknowledgment tone generation, and
distortion measurements. Refer to the Control Register
B Description below for details.
Bit Name Function Description
b0 TOUT
Tone output A logic 1 enables the tone output. This function can be implemented in either the burst
mode or nonburst mode.
b1 CP/DTMF Mode control
In DTMF mode (logic 0), the device is capable of generating and receiving DTMF signals.
When the call progress (CP) mode is selected (logic 1), a 6th-order bandpass filter is enabled to allow
call progress tones to be detected. Call progress tones within the specified bandwidth will be presented
at the IRQ/CP pin in rectangular wave format if the IRQ bit has been enabled (b2 = 1). Also, when the
CP mode and burst mode have both been selected, the transmitter will issue DTMF signals with a burst
and pause of 102 ms (typ) duration. This signal duration is twice that obtained from the DTMF transmit-
ter, if DTMF mode had been selected. Note that DTMF signals cannot be decoded when the CP mode
has been selected.
b2 IRQ Interrupt enable A logic 1 enables the interrupt mode. When this mode is active and the DTMF mode has
been selected (b1 = 0), the IRQ/CP pin will pull to a logic 0 condition when either (1) a valid DTMF sig-
nal has been received and has been present for the guard time or (2) the transmitter is ready for more
data (burst mode only).
b3 RSEL Register select A logic 1 selects control register B on the next write cycle to the control register address. Subsequent
write cycles to the control register are directed back to control register A.
Rev. 1 www.clare.com
5

5 Page





M-8888-01 arduino
Test Loads
Timing Diagrams
M-8888
Rev. 1 www.clare.com
11

11 Page







PáginasTotal 14 Páginas
PDF Descargar[ Datasheet M-8888-01.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
M-8888-01DTMF TransceiverClare  Inc.
Clare Inc.
M-8888-01PDTMF TransceiverClare  Inc.
Clare Inc.
M-8888-01SMDTMF TransceiverClare  Inc.
Clare Inc.
M-8888-01TDTMF TransceiverClare  Inc.
Clare Inc.

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar