DataSheet.es    


PDF A3212EUA Data sheet ( Hoja de datos )

Número de pieza A3212EUA
Descripción MICROPOWER/ ULTRA-SENSITIVE HALL-EF FECT SWITCH
Fabricantes Allegro MicroSystems 
Logotipo Allegro MicroSystems Logotipo



Hay una vista previa y un enlace de descarga de A3212EUA (archivo pdf) en la parte inferior de esta página.


Total 12 Páginas

No Preview Available ! A3212EUA Hoja de datos, Descripción, Manual

A3212
Package Sufx ‘LH’ Pinning
(SOT23W)
3
V
DD
1
2
Dwg. PH-016-1
Pinning is shown viewed from branded side.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VDD .............................. 5 V
Magnetic Flux Density, B .......... Unlimited
Output Off Voltage, VOUT ...................... 5 V
Output Current, IOUT ........................... 1 mA
Junction Temperature, TJ ................ +170°C
Operating Temperature, TA
Range 'E-' .................... -40°C to +85°C
Range 'L-' .................. -40°C to +150°C
Storage Temperature Range,
TS .............................. -65°C to +170°C
Caution: These CMOS devices have input
static protection (Class 3) but are still sus-
ceptible to damage if exposed to extremely
high static electrical charges.
MICROPOWER, ULTRA-SENSITIVE
HALL-EFFECT SWITCH
The A3212 integrated circuit is an ultra-sensitive, pole independent Hall-
effect switch with a latched digital output. This sensor is especially suited for
operation in battery-operated, hand-held equipment such as cellular and cordless
telephones, pagers, and palmtop computers. A 2.5 volt to 3.5 volt operation and a
unique clocking scheme reduce the average operating power requirements to less
than 15 µW with a 2.75 volt supply.
Unlike other Hall-effect switches, either a north or south pole of sufcient
strength will turn the output on; in the absence of a magnetic eld, the output
is off. The polarity independence and minimal power requirement allow these
devices to easily replace reed switches for superior reliability and ease of manu-
facturing, while eliminating the requirement for signal conditioning.
Improved stability is made possible through chopper stabilization (dynamic
offset cancellation), which reduces the residual offset voltage normally caused
by device overmolding, temperature dependencies, and thermal stress.
This device includes on a single silicon chip a Hall-voltage generator,
small-signal amplier, chopper stabilization, a latch, and a MOSFET output.
Advanced BiCMOS processing is used to take advantage of low-voltage and
low-power requirements, component matching, very low input-offset errors, and
small component geometries.
Three package styles provide a magnetically optimized package for most ap-
plications. Package sufxes 'EH' and ‘LH’ are for miniature low-prole (lead-
less and leaded, respectively) surface-mount packages while sufx ‘UA’ is for
a three-lead SIP for through-hole mounting. Each package is available in a lead
(Pb) free version (sufx, –T) with 100% matte tin plated leadframe.
FEATURES
Micropower Operation
Operation with North or South Pole
2.5 V to 3.5 V Battery Operation
Chopper Stabilized
Superior Temperature Stability
Extremely Low Switch-Point Drift
Insensitive to Physical Stress
ESD Protected to 5 kV
Solid-State Reliability
Small Size
Easily Manufacturable with Magnet Pole Independence

1 page




A3212EUA pdf
3212
MICROPOWER,
ULTRA-SENSITIVE
HALL-EFFECT SWITCH
TYPICAL OPERATING CHARACTERISTICS
SWITCH POINTS
60 60
40 BOPS
BRPS
20
40 BOPS
BRPS
20
0
VDD = 2.75 V
0
TA = 25°C
-20
-40
-60
-50
-25
BRPN
BOPN
0 25 50 75 100
AMBIENT TEMPERATURE IN °C
125 150
Dwg. GH-027-3
-20
-40
-60
2.4
BRPN
BOPN
2.6 2.8 3.0 3.2
SUPPLY VOLTAGE IN VOLTS
3.4 3.6
Dwg. GH-057-2
SUPPLY CURRENT
7.0 7.0
6.0
5.0 VDD =2.75 V
VDD =3.5 V
VDD =2.5 V
4.0
6.0
5.0
4.0
TA = 25°C
3.0
-50
-25
0 25 50 75 100
AMBIENT TEMPERATURE IN °C
125 150
Dwg. GH-028-11
www.allegromicro.com
3.0
2.4
2.6 2.8 3.0 3.2
SUPPLY VOLTAGE IN VOLTS
3.4 3.6
Dwg. GH-058-7
5

5 Page





A3212EUA arduino
A3212
MICROPOWER,
ULTRA-SENSITIVE
HALL-EFFECT SWITCH
PACKAGE DESIGNATOR ‘UA’
Dimensions in Inches
(controlling dimensions)
Dimensions in Millimeters
(for reference only)
0.164
0.159
4.17
4.04
0.062
45° 0.058
1.57
45° 1.47
0.122
0.117
0.085 1 2 3 0.031
MAX
0.640
0.600
45°
0.0173
0.0138
SEE NOTE
0.0189
0.0142
0.050
BSC
Dwg. MH-014E in
3.10
2.97
2.16 1 2 3 0.79
MAX
16.26
15.24
45°
0.44
0.35
SEE NOTE
0.48
0.36
1.27
BSC
Dwg. MH-014E mm
NOTES: 1. Tolerances on package height and width represent
allowable mold offsets. Dimensions given are measured
at the widest point (parting line).
2. Exact body and lead configuration at vendor’s option
within limits shown.
3. Height does not include mold gate flash.
4. Recommended minimum PWB hole diameter to clear
transition area is 0.035" (0.89 mm).
5. Where no tolerance is specified, dimension is nominal.
115 Northeast Cutoff, Box 15036
11 Worcester, Massachusetts 01615-0036 (508) 853-5000

11 Page







PáginasTotal 12 Páginas
PDF Descargar[ Datasheet A3212EUA.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
A3212EUAMICROPOWER/ ULTRA-SENSITIVE HALL-EF FECT SWITCHAllegro MicroSystems
Allegro MicroSystems
A3212EUA-TMICROPOWER/ ULTRA-SENSITIVE HALL-EF FECT SWITCHAllegro MicroSystems
Allegro MicroSystems

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar