DataSheet.es    


PDF A3195LU Data sheet ( Hoja de datos )

Número de pieza A3195LU
Descripción PROTECTED/ HIGH-TEMPERATURE/ HALL-EFFECT LATCH WITH ACTIVE PULL-DOWN
Fabricantes Allegro MicroSystems 
Logotipo Allegro MicroSystems Logotipo



Hay una vista previa y un enlace de descarga de A3195LU (archivo pdf) en la parte inferior de esta página.


Total 10 Páginas

No Preview Available ! A3195LU Hoja de datos, Descripción, Manual

3195
PROTECTED, HIGH-TEMP.,
3195ACTIVE PULL-DOWN
HALL-EFFECT LATCH
PROTECTED, HIGH-TEMPERATURE,
HALL-EFFECT LATCH WITH ACTIVE PULL-DOWN
LATCH
12
3
Dwg. PH-013
Pinning is shown viewed from branded side.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, VCC (100 ms) .......... 115 V*
(continuous) ................................... 26 V
Reverse Battery Voltage,
VRCC (100 ms) ............................ -100 V
(continuous) ................................. -30 V
Magnetic Flux Density, B ........... Unlimited
Reverse Output Voltage, VOUT ......... -0.5 V
Continuous Output Current,
IOUT ........................... Internally Limited
Package Power Dissipation,
PD ........................................ See Graph
Junction Temperature, TJ ................. 170°C
Operating Temperature Range, TA
Suffix “E–” .................... -40°C to +85°C
Suffix “L–” .................. -40°C to +150°C
Storage Temperature, TS ................. 170°C
*Fault condition, internal overvoltage shutdown
above 28 V.
These Hall-effect latches are capable of sensing magnetic fields
while using an unprotected power supply. The A3195– can provide
position and speed information by providing a digital output for mag-
netic fields that exceed their predefined switch points. These devices
operate down to zero speed and have switch points that are designed
to be extremely stable over a wide operating temperature and voltage
range. The latching characteristics make them ideal for use in pulse
counting applications when used with a multi-pole ring magnet.
A 25 mA high-side driver combined with an active pull-down is espe-
cially useful for driving capacitive loads. Output short-circuit protection
allows for an increased wiring harness fault tolerance. The tempera-
ture compensated switch points, the wide operating voltage range, and
the integrated protection make these devices ideal for use in automo-
tive applications such as transmission speed sensors and integrated
wheel bearing speed sensors.
Each monolithic device contains an integrated Hall-effect trans-
ducer, a temperature-compensated comparator, a voltage regulator,
and a buffered high-side driver with an active pull-down. Supply
protection is made possible by the integration of overvoltage shutdown
circuitry that monitors supply fault conditions. Output protection
circuitry includes source and sink current current limiting for short
circuits to supply or ground.
The A3195E– is rated for operation over a temperature range of
-40°C to +85°C; the A3195L– is rated for operation over an extended
temperature range of -40°C to +150°C. They are supplied in a three-
lead SIP (suffix –U) or a surface-mount SOT-89 (suffix –LT).
FEATURES
s Internal Protection For Automotive (ISO/DIN) Transients
s Operation From Unregulated Supply
s Reverse Battery Protection
s Undervoltage Lockout
s Supply Noise-Suppression Circuitry
s Output Short-Circuit Protection
s Output Zener Clamp
s Thermal Protection
s Symmetrical Latching Switch Points
s Operable with Multipole Ring Magnets
Always order by complete part number, e.g., A3195LU .

1 page




A3195LU pdf
3195
PROTECTED, HIGH-TEMP.,
ACTIVE PULL-DOWN
HALL-EFFECT LATCH
3.8 V TO 26 V
WITH TRANSIENTS
VCC
1
C BYPASS
2
X
3 TO µP
CL
RL
Dwg. EH-007
OPERATION
In operation, the output transistor is OFF
until the strength of the magnetic field
perpendicular to the surface of the chip
exceeds the threshold or operate point (BOP).
When the field strength exceeds BOP, the
output transistor switches ON (a logic low)
and is capable of sinking 35 mA of current.
The output transistor switches OFF (a
logic high) when magnetic field reversal
results in a magnetic flux density below the
OFF threshold (BRP). This is illustrated in the
transfer characteristics graph. Note that the
device latches; that is, a south pole of
sufficient strength will turn the device ON.
Removal of the south pole will leave the
device ON. The presence of a north pole of
sufficient strength is required to turn the
device OFF.
The switch points increase in sensitivity
with increasing temperature to compensate
for the typical ferrite magnet temperature
characteristic. The simplest form of magnet
that will operate these devices is a ring
magnet. Other methods of operation are
possible.
TEST CIRCUIT AND
TYPICAL APPLICATION
An external 0.1 µF to 0.47 µF capacitor, with good high-frequency
characteristics, should be connected between terminals 1 and 2 to
bypass high-voltage noise and reduce EMI susceptibility.
Internal Pull-Down Resistor. An internal pull-down resistor
(nominal 15 k) is provided to allow testing of the device without the
need for an external load.
20
18
16
14
12
10
-50
-25
0 25 50 75 100
AMBIENT TEMPERATURE IN °C
125 150
Dwg. GH-060

5 Page










PáginasTotal 10 Páginas
PDF Descargar[ Datasheet A3195LU.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
A3195LLTPROTECTED/ HIGH-TEMPERATURE/ HALL-EFFECT LATCH WITH ACTIVE PULL-DOWNAllegro MicroSystems
Allegro MicroSystems
A3195LUPROTECTED/ HIGH-TEMPERATURE/ HALL-EFFECT LATCH WITH ACTIVE PULL-DOWNAllegro MicroSystems
Allegro MicroSystems

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar