DataSheet.es    


PDF A29L040 Data sheet ( Hoja de datos )

Número de pieza A29L040
Descripción 512K X 8 Bit CMOS 3.0 Volt-only/ Uniform Sector Flash Memory
Fabricantes AMIC Technology 
Logotipo AMIC Technology Logotipo



Hay una vista previa y un enlace de descarga de A29L040 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! A29L040 Hoja de datos, Descripción, Manual

A29L040 Series
Preliminary
512K X 8 Bit CMOS 3.0 Volt-only,
Uniform Sector Flash Memory
Document Title
512K X 8 Bit CMOS 3.0 Volt-only, Uniform Sector Flash Memory
Revision History
Rev. No.
0.0
0.1
History
Initial issue
Add 32-pin DIP package type
Issue Date
December 10, 2002
June 25, 2003
Remark
Preliminary
PRELIMINARY (June, 2003, Version 0.1)
AMIC Technology, Corp.

1 page




A29L040 pdf
A29L040 Series
Absolute Maximum Ratings*
Storage Temperature Plastic Packages . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0°C to + 70°C
. . . . . . . . . . . . . . . . . . . . . . for -U series: -45°C to +85°C
Ambient Temperature with Power Applied . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to + 70°C
. . . . . . . . . . . . . . . . . . . . . . for -U series: -45°C to +85°C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +4.0V
A9 & OE (Note 2) . . . . . . . . . . . . . . . . . . . . -0.5 to +12.5V
All other pins (Note 1) . . . . . . . . . . . . -0.5V to VCC + 0.5V
Output Short Circuit Current (Note 3) . . . . . . . . . 200mA
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5V.
During voltage transitions, input or I/O pins may
undershoot VSS to -2.0V for periods of up to 20ns.
Maximum DC voltage on input and I/O pins is VCC
+0.2V. During voltage transitions, input or I/O pins may
overshoot to VCC +2.0V for periods up to 20ns.
2. Minimum DC input voltage on A9 and OE is -0.5V.
During voltage transitions, A9 and OE may overshoot
VSS to -2.0V for periods of up to 20ns. Maximum DC
input voltage on A9 is +12.5V which may overshoot to
14.0V for periods up to 20ns.
3. No more than one output is shorted at a time. Duration
of the short circuit should not be greater than one
second.
*Comments
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of
this device at these or any other conditions above
those indicated in the operational sections of these
specification is not implied or intended. Exposure to
the absolute maximum rating conditions for extended
periods may affect device reliability.
Operating Ranges
Commercial (C) Devices
Ambient Temperature (TA) . . . . . . . . . . . . . . 0°C to +70°C
Extended Range Devices
Ambient Temperature (TA) . . . . . . . . . . . . -45°C to +85°C
VCC Supply Voltages
VCC for all devices . . . . . . . . . . . . . . . . . . +2.7V to +3.6V
Operating ranges define those limits between which the
functionally of the device is guaranteed.
Device Bus Operations
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself
does not occupy any addressable memory location. The
register is composed of latches that store the commands,
along with the address and data information needed to
execute the command. The contents of the register serve
as inputs to the internal state machine. The state machine
outputs dictate the function of the device. The appropriate
device bus operations table lists the inputs and control
levels required, and the resulting output. The following
subsections describe each of these operations in further
detail.
Operation
Read
Write
CMOS Standby
TTL Standby
Output Disable
Table 1. A29L040 Device Bus Operations
CE OE WE
L LH
L HL
VCC ± 0.3 V
X
X
H XX
L HH
A0 – A18
AIN
AIN
X
X
X
I/O0 - I/O7
DOUT
DIN
High-Z
High-Z
High-Z
Legend:
L = Logic Low = VIL, H = Logic High = VIH, VID = 12.0 ± 0.5V, X = Don't Care, DIN = Data In, DOUT = Data Out, AIN = Address In
Note: See the "Sector Protection/Unprotection" section, for more information.
PRELIMINARY (June, 2003, Version 0.1)
4
AMIC Technology, Corp.

5 Page





A29L040 arduino
A29L040 Series
Table 4. A29L040 Command Definitions
Command
Sequence
(Note 1)
First
Second
Addr Data Addr Data
Read (Note 5)
1 RA RD
Reset (Note 6)
1 XXX F0
Manufacturer ID
4 555 AA 2AA 55
Device ID
Autoselect
(Note 7) Continuation ID
4 555 AA
4 555 AA
Sector Protect Verify 4 555 AA
(Note 8)
2AA 55
2AA 55
2AA 55
Program
Chip Erase
Sector Erase
Erase Suspend (Note 9)
Erase Resume (Note 10)
4 555 AA
6 555 AA
6 555 AA
1 XXX B0
1 XXX 30
2AA 55
2AA 55
2AA 55
Bus Cycles (Notes 2 - 4)
Third
Fourth
Fifth
Sixth
Addr Data Addr Data Addr Data Addr Data
555 90 X00 37
555 90 X01 92
555 90 X03 7F
555 90 SA 00
X02 01
555 A0 PA PD
555 80 555 AA 2AA 55 555 10
555 80 555 AA 2AA 55 SA 30
Legend:
X = Don't care
RA = Address of the memory location to be read.
RD = Data read from location RA during read operation.
PA = Address of the memory location to be programmed. Addresses latch on the falling edge of the WE or CE pulse,
whichever happens later.
PD = Data to be programmed at location PA. Data latches on the rising edge of WE or CE pulse, whichever happens first.
SA = Address of the sector to be verified (in autoselect mode) or erased. Address bits A18 - A16 select a unique sector.
Note:
1. See Table 1 for description of bus operations.
2. All values are in hexadecimal.
3. Except when reading array or autoselect data, all bus cycles are write operation.
4. Address bits A18 - A11 are don't cares for unlock and command cycles, unless SA or PA required.
5. No unlock or command cycles required when reading array data.
6. The Reset command is required to return to reading array data when device is in the autoselect mode, or if I/O5 goes
high (while the device is providing status data).
7. The fourth cycle of the autoselect command sequence is a read cycle.
8. The data is 00h for an unprotected sector and 01h for a protected sector. See "Autoselect Command Sequence" for
more information.
9. The system may read and program in non-erasing sectors, or enter the autoselect mode, when in the Erase Suspend
mode.
10. The Erase Resume command is valid only during the Erase Suspend mode.
PRELIMINARY (June, 2003, Version 0.1)
10
AMIC Technology, Corp.

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet A29L040.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
A29L040512K X 8 Bit CMOS 3.0 Volt-only/ Uniform Sector Flash MemoryAMIC Technology
AMIC Technology
A29L040-70512K X 8 Bit CMOS 3.0 Volt-only/ Uniform Sector Flash MemoryAMIC Technology
AMIC Technology
A29L040A512K X 8 Bit CMOS 3.0 Volt-only Uniform Sector Flash MemoryAMIC Technology
AMIC Technology
A29L040L-70512K X 8 Bit CMOS 3.0 Volt-only/ Uniform Sector Flash MemoryAMIC Technology
AMIC Technology

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar