DataSheet.es    


PDF R5370EA18K Data sheet ( Hoja de datos )

Número de pieza R5370EA18K
Descripción Distributed Gate Thyristor
Fabricantes IXYS 
Logotipo IXYS Logotipo



Hay una vista previa y un enlace de descarga de R5370EA18K (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! R5370EA18K Hoja de datos, Descripción, Manual

Date:- 11th May, 2017
Data Sheet Issue:- A3
Distributed Gate Thyristor
Types R5370EA18# and R5370EA22#
Absolute Maximum Ratings
VDRM
VDSM
VRRM
VRSM
VOLTAGE RATINGS
Repetitive peak off-state voltage, (note 1)
Non-repetitive peak off-state voltage, (note 1)
Repetitive peak reverse voltage, (note 1)
Non-repetitive peak reverse voltage, (note 1)
IT(AVM)
IT(AVM)
IT(AVM)
IT(RMS)
IT(d.c.)
ITSM
ITSM2
I2t
I2t
(di/dt)cr
VRGM
PG(AV)
PGM
Tj op
Tstg
OTHER RATINGS
Maximum average on-state current, Tsink=55°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 2)
Maximum average on-state current. Tsink=85°C, (note 3)
Nominal RMS on-state current, Tsink=25°C, (note 2)
D.C. on-state current, Tsink=25°C, (note 4)
Peak non-repetitive surge tp=10ms, Vrm=0.6VRRM, (note 5)
Peak non-repetitive surge tp=10ms, Vrm10V, (note 5)
I2t capacity for fusing tp=10ms, Vrm=0.6VRRM, (note 5)
I2t capacity for fusing tp=10ms, Vrm10V, (note 5)
Critical rate of rise of on-state current (repetitive), (Note 6)
Critical rate of rise of on-state current (non-repetitive), (Note 6)
Peak reverse gate voltage
Mean forward gate power
Peak forward gate power
Operating temperature range
Storage temperature range
Notes:-
1) De-rating factor of 0.13% per °C is applicable for Tj below 25°C.
2) Double side cooled, single phase; 50Hz, 180° half-sinewave.
3) Cathode side cooled, single phase; 50Hz, 180° half-sinewave.
4) Double side cooled.
5) Half-sinewave, 125°C Tj initial.
6) VD=67% VDRM, IFG=2A, tr0.5µs, Tcase=125°C.
MAXIMUM
LIMITS
1800-2200
1900-2300
1800-2200
1900-2300
UNITS
V
V
V
V
MAXIMUM
LIMITS
5370
3510
1665
10905
8760
70
76.8
24.5×106
29.5×106
500
1000
5
5
50
-40 to +125
-40 to +150
UNITS
A
A
A
A
A
kA
kA
A2s
A2s
A/µs
A/µs
V
W
W
°C
°C
Data Sheet. Types R5370EA18# and R5370EA22# Issue A3
Page 1 of 13
May, 2017

1 page




R5370EA18K pdf
Distributed Gate Thyristor types R5370EA18# and R5370EA22#
15.0 Reverse Recovery Loss
15.1 Determination by Measurement
From waveforms of recovery current obtained from a high frequency shunt (see Note 1, Page 5) and
reverse voltage present during recovery, an instantaneous reverse recovery loss waveform must be
constructed. Let the area under this waveform be E joules per pulse. A new heat sink temperature can
then be evaluated from the following:
( )TSINK (new) = TSINK (original) E k + f Rth(J Hs)
Where k=0.227 (°C/W)/s
E = Area under reverse loss waveform per pulse in joules (W.s.)
f = rated frequency Hz at the original heat sink temperature.
Rth(J-Hs) = d.c. thermal resistance (°C/W).
The total dissipation is now given by:
W(TOT) = W(original) + E f
15.2 Determination without Measurement
In circumstances where it is not possible to measure voltage and current conditions, or for design
purposes, the additional losses E in joules may be estimated as follows.
Let E be the value of energy per reverse cycle in joules (curves in Figure 9).
Let f be the operating frequency in Hz
( )TSINK (new) = TSINK (original ) E Rth f
Where TSINK (new) is the required maximum heat sink temperature and
TSINK (original) is the heat sink temperature given with the frequency ratings.
A suitable R-C snubber network is connected across the thyristor to restrict the transient reverse voltage
to a peak value (Vrm) of 67% of the maximum grade. If a different grade is being used or Vrm is other than
67% of Grade, the reverse loss may be approximated by a pro rata adjustment of the maximum value
obtained from the curves.
NOTE 1- Reverse Recovery Loss by Measurement
This thyristor has a low reverse recovered charge and peak reverse recovery current. When measuring
the charge, care must be taken to ensure that:
(a) a.c. coupled devices such as current transformers are not affected by prior passage of high
amplitude forward current.
(b) A suitable, polarised, clipping circuit must be connected to the input of the measuring oscilloscope
to avoid overloading the internal amplifiers by the relatively high amplitude forward current signal
(c) Measurement of reverse recovery waveform should be carried out with an appropriate critically
damped snubber, connected across diode anode to cathode. The formula used for the calculation
of this snubber is shown below:
R2 = 4 Vr
CS
di
dt
Vr = Commutating source voltage
Where: CS = Snubber capacitance
R = Snubber resistance
Data Sheet. Types R5370EA18# and R5370EA22# Issue A3
Page 5 of 13
May, 2017

5 Page





R5370EA18K arduino
Figure 13 - Square wave frequency ratings
Distributed Gate Thyristor types R5370EA18# and R5370EA22#
Figure 14 - Square wave frequency ratings
Figure 15 - Square wave frequency ratings
Figure 16 - Square wave frequency ratings
Data Sheet. Types R5370EA18# and R5370EA22# Issue A3
Page 11 of 13
May, 2017

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet R5370EA18K.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
R5370EA18JDistributed Gate ThyristorIXYS
IXYS
R5370EA18KDistributed Gate ThyristorIXYS
IXYS

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar