DataSheet.es    


PDF DLW5ATZ501MQ2B Data sheet ( Hoja de datos )

Número de pieza DLW5ATZ501MQ2B
Descripción Wire Wound Chip Common Mode Choke Coil
Fabricantes Murata 
Logotipo Murata Logotipo



Hay una vista previa y un enlace de descarga de DLW5ATZ501MQ2B (archivo pdf) en la parte inferior de esta página.


Total 11 Páginas

No Preview Available ! DLW5ATZ501MQ2B Hoja de datos, Descripción, Manual

Reference Only
Spec. No. JEFL243C-9122-01
P 1/11
Wire Wound Chip Common Mode Choke Coil
DLW5ATH□□□MQ2Murata Standard Reference Specification [AEC-Q200]
1. Scope
This reference specification applies to Wire Wound Chip Common Mode Choke Coil DLW5ATH_MQ Series for
Automotive Electronics based on AEC-Q200.
2. Part Numbering
(ex.) DL W 5A T H 111 M Q 2 L
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10)
(1) Chip Common Mode Choke Coil
(2) Structure (W : Winding Type)
(3) Dimension (L×W)
(4) Type
(5) Category
3.Rating
(6) Impedance (Typ. at 100MHz)
(7) Circuit
(8) Features
(9) Number of Line
(10) Packaging Code L : Taping (φ180mm/reel)
K : Taping (φ330mm/reel)
B : Bulk
Customer
Part Number
MURATA
Part Number
DLW5ATH500MQ2L
Impedance
at 10MHz,
Under Standard
Testing Conditions
()
Impedance
at 100MHz,
Under Standard
Testing Conditions
(Typ.)
Rated
Voltage
V(DC)
Withstanding
Voltage
V(DC)
Rated
Current(*)(A)
at
105
at
125
DLW5ATH500MQ2K
4.6min
50
4.0 2.5
DLW5ATH500MQ2B
DLW5ATH151MQ2L
DLW5ATH151MQ2K
11min
150
3.0 2.0
DLW5ATH151MQ2B
DLW5ATH331MQ2L
DLW5ATH331MQ2K
20min
330 50 125 2.5 1.5
DLW5ATH331MQ2B
DLW5ATH501MQ2L
DLW5ATH501MQ2K
35min
500
2.0 1.2
DLW5ATZ501MQ2B
DLW5ATH112MQ2L
DLW5ATH112MQ2K
50min
1100
1.5 1.0
DLW5ATH112MQ2B
DC
Resistance
(Rdc)
(max.)
0.013
0.020
0.027
0.034
0.056
Insulation
Resistance
(Mmin.)
10
ESD
Rank
2.2kV
2
(*)As for DLW5ATH_MQ type Rated Current is derated as following figure depending on the operating temperature.
Rated Current
at 105
Rated Current
at 125
Operating Temperature
(Ambient temperature)[]
105
125
· Operating Temperature : - 40 °C to + 125 °C
· Storage Temperature : - 40 °C to + 125 °C
MURATA MFG CO., LTD.

1 page




DLW5ATZ501MQ2B pdf
Reference Only
Spec. No. JEFL243C-9122-01
12. Specification of Packaging
12.1 Appearance and Dimensions
φ1.5
0.1
0
4.0±0.1
2.0±0.05
0.3±0.05
P 5/11
*Dimension of the Cavity is measured
at the bottom side.
4.1±0.1
8.0±0.1
Direction of feed
2.7±0.1
(in mm)
12.2 Specification of Taping
(1) Packing quantity (Standard quantity) φ180 mm reel : 700 pcs. / reel φ330 mm reel :2500 pcs. / reel
(2) Packing Method
Products shall be packaged in each embossed cavity of plastic tape and sealed with cover tape.
(3) Sprocket Hole
The sprocket holes are to the right as the tape is pulled toward the user.
(4) Spliced point
The cover tape have no spliced point.
(5) Missing components number
Missing components number within 0.1% of the number per reel or 1 pc., whichever is greater,
and are not continuous. The specified quantity per reel is kept.
12.3 Pull Strength of Plastic Tape
Plastic Tape
Cover Tape
5 N min.
10 N min.
12.4 Peeling off force of Cover Tape
0.2N to 0.7N (minimum value is typical.)
Speed of Peeling off : 300 mm / min
165 to 180 degree F
Cover tape
Plastic tape
12.5 Dimensions of Leader-tape, Trailer and Reel
There shall be leader-tape (cover tape only and empty tape) and trailer-tape (empty tape) as follows.
« Packaging Code : L (φ180mm reel) »
2.0±0.5
Trailer
160 min.
Label
Leader
190 min. 210 min.
Empty Tape Cover tape
φ 60±10
13±
1
0
17±1.4
φ
180±
0
3
φ 13.0±0.2
φ 21.0±0.8
Direction of feed
(in mm)
« Packaging Code : K (φ330mm reel) »
φ50 min.
2.0±0.5
14±1.5
2.0±0.5
Trailer
160 min.
Label
φ 13.0±0.5
φ 21.0±0.8
Leader
190 min. 210 min.
Empty Tape Cover tape
Direction of feed
φ 330±2.0
(in mm)
MURATA MFG CO., LTD.

5 Page





DLW5ATZ501MQ2B arduino
Reference Only
Spec. No. JEFL243C-9122-01
P 11/11
14.13 Storage condition
(1) Storage period
Use the products within 12 months after delivered.
Solderability should be checked if this period is exceeded.
(2) Storage environment conditions
· Products should be stored in the warehouse on the following conditions.
Temperature : -10 °C to +40 °C
Humidity
: 15 % to 85% relative humidity No rapid change on temperature and humidity.
·Products should not be stored in corrosive gases, such as sulfureous, acid gases, alkaline gases,
to prevent the following deterioration.
Poor solderabirity due to the oxidized electrode.
·Products should be stored on the palette for the prevention of the influence from humidity, dust and so on.
·Products should be stored in the warehouse without heat shock, vibration, direct sunlight and so on.
·Products should not be stored under the air tights packaged condition.
(3) Delivery
Care should be taken when transporting or handling product to avoid excessive vibration or mechanical shock.
15. ! Note
(1)Please make sure that your product has been evaluated in view of your specifications with our product being
mounted to your product.
(2)You are requested not to use our product deviating from the reference specifications.
(3)The contents of this reference specification are subject to change without advance notice. Please approve our
product specifications or transact the approval sheet for product specifications before ordering.
MURATA MFG CO., LTD.

11 Page







PáginasTotal 11 Páginas
PDF Descargar[ Datasheet DLW5ATZ501MQ2B.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
DLW5ATZ501MQ2BWire Wound Chip Common Mode Choke CoilMurata
Murata

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar