|
|
PDF BM92A11MWV-Z Data sheet ( Hoja de datos )
| Número de pieza | BM92A11MWV-Z | |
| Descripción | USB Type-C Power Delivery Controller | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BM92A11MWV-Z (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
|
No Preview Available !
Datasheet
USB Type-C Power Delivery Controller
BM92A11MWV-Z
General Description
BM92A11 is a full function USB Type-C Power Delivery
(PD) controller that supports USB Power Delivery using
base-band communication. It is compatible with USB
Type-C Specification and USB Power Delivery
specification.
BM92A11 includes support for the PD policy engine and
communicates with an Embedded Controller or the SoC
via host interface. It supports SOP, SOP’ and SOP’’
signaling, allowing it to communicate with cable marker
ICs, support alternate modes.
Key Specifications
VBUS Voltage Range:
4.75V to 20V
Power Sink Voltage Range:
4.75V to 20V
Power Source Voltage Range:
4.75V to 5.5V
Power Consumption at Sleep Power: 0.4mW(Typ)
Operating Temperature Range: -30°C to +105°C
Package
UQFN40V5050A
W (Typ) x D (Typ) x H (Max)
5.00mm x 5.00mm x 1.00mm
Features
USB Type-C Specification compatible
USB PD Specification compatible (BMC-PHY)
Connected the required initial voltage is 12V
Request current depends on the far-end device
Start of automatic power receiving without Ext-MCU
Two channel power path control using N-channel
MOSFET drivers with back flow prevention
Type-C cable orientation detection
Built-in VCONN Switch and VCONN controller
Direct VBUS powered operation
Initial Role is UFP mode (Supports DFP/DRP mode)
Supports Dead Battery operation
SMBus Interface for Host Communication
Applications
Consumer Applications
Laptop PCs, Tablet PCs
Typical Application Circuit
VBUS
GND
VCONN
CC1
CC2
USB Type-C
Receptacle
GND
VCONN_IN
CC1
CC2
XCLPOFF1
XCLPOFF2
Hi-side
Switch
GND
GND
GND
GND
VDDIO
SMDATA
VDDIO
SMCLK
GPIO0（VIN_EN)
GPIO1（ALERT#)
BM92A11MWV-Z
GPO2/VDIV(BST_EN)
GPO3/FB(HSSWEN)
UQFN40V5050A
GPIO7
GPIO6
GPIO5
GPIO4
GND
Charger Power
Power Supply
For Prov (5V)
VSVR
(3.1V～5.5V)
VDDIO
(1.7V～5.5V)
EC-I/F
VCCIN
VDDIO
DBGMODDT
DBGRSTCK
IDSEL/ATST1
VSTR/ATST2
XRST
VCCIN
GND
VCCIN
GND GND GND
GND
Figure A. Typical Application Circuit
〇Product structure : Silicon monolithic integrated circuit
.www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
〇This product has no designed protection against radioactive rays
1/33
TSZ02201-0232AA000350-1-2
06.Mar.2017 Rev.002
1 page  
BM92A11MWV-Z
2. Pin Description
PKG
PIN#
Pin Name
1 GND
2 VSTR/ATST2
3 IDSEL/ATST1
4 XRST
5 VCCIN
6 VSVR
7 DSCHG
8 GND
9 VB
10 GPIO4
11 GPIO5
12 GPIO6
13 GPIO7
14 DBGRSTCK
15 DBGMODDT
16
GPIO0
(VIN_EN)
17
GPIO1
(ALERT#)
18 VDDIO
19 SMDATA
20 SMCLK
21 S2_DRV_G1
22 S2_DRV_SRC
23 S2_DRV_G2
24 S1_DRV_G1
25 S1_DRV_SRC
26 S1_DRV_G2
(Note 1) N-ch Open Drain
Table 2-1 Pin Description
BLOCK
I/O
Type
Digital
I/O Level
Description
GND
I GND
Ground
TEST/Debug IO Analog
Analog TEST/ Debug Pin2
SMBus ID (device address)
TEST/Debug I Analog VCCIN selection “H”:1Ah, “L”:18h
/Debug Pin1
Interface
I Digital VCCIN Digital block Reset
Internal Power supply
USB-PD
O Analog
(For internal use, need to
connect capacitor to GND
POWER
I Power
5V SVR INPUT and
SPDSRC_FET_SRC voltage
Interface
IO Analog
Discharge NMOS Drain
GND
I GND
Ground
POWER
I Power
Power Source from VBUS
Interface
I Digital
Mode fixation (Fix: L)
Interface
I Digital
NC pin
Interface
I Digital
NC pin
Interface
I Digital
NC pin
TEST
IO Digital VDDIO Test for logic
TEST
IO Digital VDDIO Test for logic
Interface
I Digital VDDIO VIN_EN signal
Interface
POWER
Interface
Interface
FET Gate
Control
FET Gate
Control
FET Gate
Control
FET Gate
Control
FET Gate
Control
FET Gate
Control
O(Note 1)
I
IO
I
O
Digital
Power
Digital
Digital
VDDIO
VDDIO
VDDIO
Analog
I Analog
O Analog
O Analog
I Analog
O Analog
Alert signal
Interface Voltage
SMBus Data
SMBus Clock
Power Path FET Gate Control
SPDSNK_G1
Power Path FET BG/SRC
Voltage
SPDSNK_SRC
Power Path FET Gate Control
SPDSNK_G2
Power Path FET Gate Control
SPDSRC_G1
Power Path FET BG/SRC
Voltage
SPDSRC_SRC
Power Path FET Gate Control
SPDSRC_G2
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
5/33
TSZ02201-0232AA000350-1-2
06.Mar.2017 Rev.002
5 Page 
BM92A11MWV-Z
4.7. Power Supply Management
4.7.1. Outline
BM92A11 has a power selector. It select the lowest power supply voltage from VSVR, VEX, or VB for low power
consumption. Internal Power Supply (VCCIN) gives priority in order of VSVR, VEX, and VB. VCCIN supplied from the
power selector is used to BM92A11 main power source. LDOs (for internal only) are supplied from VCCIN, and output each
internal supply voltage.
Each power supply input have UVLO and OVLO. And POR (power on reset) signal is generated from detection of
LDO28OK, LDO15DOK, LDO15AOK, and VCCIN.
UVLO
/OVLO
signal
UVLO/OVLO
Detection
Internal
Power
Supply
LDO28OK
POR
signal
Internal
Power
Supply
VDDIO
detection
signal
POR
LDO15DOK
LDO15AOK
DET
LDO
LDO
LDO
VSVR
VEX
VB
VCCIN
LDO28CAP
LDO15DCAP
LDO15ACAP
VDDIO
VBUS 0V
VEX
0V
VSVR 0V
5 to 20V
5 to 20V
5V
VCCIN 0V
VBUS
VEX
VSVR
Figure 4-1 Power Supply Management Block Diagram and Timing Chart
www.rohm.com
© 2017 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
11/33
TSZ02201-0232AA000350-1-2
06.Mar.2017 Rev.002
11 Page | ||
| Páginas | Total 30 Páginas | |
| PDF Descargar | [ Datasheet BM92A11MWV-Z.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BM92A11MWV-Z | USB Type-C Power Delivery Controller | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |