|
|
Número de pieza | GDEW012 | |
Descripción | LCD Module | |
Fabricantes | DALIAN GOOD DISPLAY | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de GDEW012 (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
No Preview Available ! Good Display
EPAPER SPECIFICATIONS
GDEW012
SPEC NO
REV NO
Good Display
Specifications
Dalian Good Display Co., Ltd.
Good Display
No.17 Gonghua Street, Shahekou District, Dalian 116021 China
Tel: +86-411-84619565 Fax: +86-411-84619585
E-mail: inf [email protected]
Website: www.good-display.com
1 page Product Specification
4. Mechanical Drawing of EPD module
GDEW012
Ver 1.2
Nov.02.2015
Dalian Good Display Co., Ltd.
5 / 23
5 Page Product Specification
SGM_FL: SEGMENT & BG power selection.
0: SEGMENT & BG: floating when power OFF
1: SEGMENT & BG: Ground when power OFF. (Default)
VCOM_FL: VCOM power selection.
0: COM floating when power OFF
1: COM ground when power OFF. (Default)
This command only active when BUSY_N = "1".
GDEW012
(4) Power ON (PON) (Register: R04h)
Action
W/R D/CX D7 D6 D5 D4 D3 D2 D1 D0
Turning ON the power
0
0 00000100
After the Power ON command, the driver will be powered ON following the Power ON Sequence.
After the Power ON command and all power sequence are ready, the BUSY_N signal will become "1".
Please refer to the Power ON Sequence section.
(5) Data Start Transmission (DTM) (R10h)
Action
R/W D/CX D7 D6 D5 D4 D3 D2 D1 D0
0 0 0 001 0 0 0 0
0 1 Pixel1 Pixel2 Pixel3 Pixel4 Pixel5 Pixel6 Pixel7 Pixel8
0 1 .. .. .. .. .. .. .. ..
Start Data
0 1 Pixel33 Pixel34 Pixel35 Pixel36 Pixel37 Pixel38 Pixel39 Pixel40
Transmission
0 1 Pixel41 Pixel42 Pixel43 Pixel44 0
000
(14-byte command) 0
1 Pixel49 Pixel50 Pixel51 Pixel52 Pixel53 Pixel54 Pixel55 Pixel56
0 1 .. .. .. .. .. .. .. ..
0 1 Pixel89 Pixel90 Pixel91 Pixel92 Pixel93 Pixel94 Pixel95 Pixel96
0 1 BG - - - - - - -
The register starts to transmit data and write to SRAM. To complete data transmission, command DSP (Data
transmission Stop) must be issued. Then the chip will start to send data/VCOM for panel.
This command only active when BUSY_N = "1".
(6) Data Stop (DSP) (R11h)
Action
W/R D/CX D7 D6 D5 D4 D3 D2 D1 D0
Stopping data
00
0 0010001
transmission
0 1 data_flag - - - - - - -
To stop data transmission, this command must be issued to check the data_flag.
Data_flag: Data flag of receiving user data.
0: Driver didn't receive all the data.
1: Driver has already received all the one frame data. BUSY_N
While user sent this command, the IC will refresh the display (data/VCOM) according to SRAM data and LUT.
This command only active when BUSY_N = "1". After data start (10h) and data stop (11h) command, BUSY_N
signal will become "0".
Ver 1.2
Nov.02.2015
Dalian Good Display Co., Ltd.
11 / 23
11 Page |
Páginas | Total 23 Páginas | |
PDF Descargar | [ Datasheet GDEW012.PDF ] |
Número de pieza | Descripción | Fabricantes |
GDEW012 | LCD Module | DALIAN GOOD DISPLAY |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |