DataSheet.es    


PDF BC1604AIBNHJH20k Data sheet ( Hoja de datos )

Número de pieza BC1604AIBNHJH20k
Descripción LCD Module
Fabricantes Bolymin 
Logotipo Bolymin Logotipo



Hay una vista previa y un enlace de descarga de BC1604AIBNHJH20k (archivo pdf) en la parte inferior de esta página.


Total 29 Páginas

No Preview Available ! BC1604AIBNHJH20k Hoja de datos, Descripción, Manual

SPECIFICATIONS FOR
LCD MODULE
MODEL NO.
BC1604AI series
VER.04
FOR MESSRS:
________________________________________________
ON DATE OF:
________________________________________________
APPROVED BY:
________________________________________________
BOLYMIN, INC.
5F, No. 38, Keya Rd., Daya Dist., Central Taiwan Science Park, Taichung City, 42881, Taiwan.
Web Site:http://www.bolymin.com.tw TEL:+886-4-25658689 FAX:+886-4-25658698

1 page




BC1604AIBNHJH20k pdf
2. Handling Instruction
2.1 Precaution in use of LCD Module
2.1.1. LCD panel is made of glass. Avoid excessive mechanical shock or applying strong
pressure on the surface of display area.
2.1.2. The polarizer used on the display surface is easily scratched and damaged. Extreme
care should be taken when handling. To clean dust or dirt off the display surface, wipe
gently with cotton, or other soft material soaked with isopropyl alcohol, ethyl alcohol, do
not use water, ketone or aromatics and never scrub hard.
2.1.3. Store the panel or module in a dark place where the temperature is 20±5and the
humidity is below 60% RH.
2.1.4. Keep LCD panels away from direct sunlight, also avoid them in high-temperature & high
humidity environment for a long period.
2.1.5. Do not input any signal before power is turned on.
2.1.6. Avoid pressing on the metal bezel, otherwise the elastomer connector could be
deformed and lose contact, resulting in missing pixels and also cause rainbow on the
display.
2.1.7. To control temperature and time of soldering is 320±10and 3-5 sec.
2.1.8. EL manufactured from the organic film, and easily affected by temperature, humidity
and other environmental impact. Long-term placement in a place will cause low quality of
the case. Therefore, unpack the cartons and start the production with the LCM within
three months after the reception of them.
2.2 Static Electricity Precautions:
2.2.1. The LCD module contains a C-MOS LSI. People who operate the LCM should wear
ESD protection equipment to prevent ESD hurt on products.
2.2.2. Do not touch any of the conductive parts such as the LSI pads; the copper leads on the
PCB and the interface terminals with any parts of the human body.
2.2.3. Do not touch the connection terminals of the display with bare hand; it will cause
disconnection or defective insulation of terminals.
2.2.4. The modules should be kept in anti-static bags or trays for storage.
2.2.5. Only properly grounded soldering irons should be used.
2.2.6. If an electric screwdriver is used, it should be grounded and shielded to prevent sparks.
2.2.7. The normal static prevention measures should be observed for work clothes and
working benches.
2.2.8. Since dry air is inductive to static, a relative humidity of 50-60% is recommended.
2.3 Operation Precautions:
2.3.1. Since applied DC voltage causes electro-chemical reactions, which deteriorate the
display, the applied pulse waveform should be a symmetric waveform such that no DC
component remains. Be sure to use the specified operating voltage.
2.3.2. Driving voltage should be kept within specified range; excess voltage will shorten
display life.
2.3.3. An electrochemical reaction due to direct current causes LCD deterioration, Avoid the
use of -Response time will be extremely delayed at lower temperature than the operating
temperature range and on the other hand at higher temperature LCD's show dark color in
them.
BC1604AI series VER.04
-5-

5 Page





BC1604AIBNHJH20k arduino
8.Interface Pin Function
8.1 Pin Description
Pin No. Symbol Level Description
1 TX
- RS-232 level output port.
2 RX
- RS-232 level input port
3 VSS 0V Ground.
4 VDD 5V System power supply input.
I2C:Data Input/output for the I2C
5
SDA
H/L
SPI:Serial data Input .
I2C:Clock Input for I2C
6
SCL
H/L
SPI:Serial Clock Input .
7
SDO
H/L SPI:Serial data output
8 /CS H/L SPI:Chip select
8.2 Jumper selection for communication
Protocol
J21H
I2C short
SPI *
RS232
*
DEMO
short
* : Open
* : Default mode=I2C
J21L
*
short
short
*
J22H
*
*
short
short
J22L
short
short
*
*
Description
100KHz max clock
100KHz max clock
5V, TTL signal
Selftest
8.3 Jumper location
BC1604AI series VER.04
- 11 -

11 Page







PáginasTotal 29 Páginas
PDF Descargar[ Datasheet BC1604AIBNHJH20k.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
BC1604AIBNHJH20kLCD ModuleBolymin
Bolymin

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar