|
|
Número de pieza | CGG128064GJ00-FHB-R | |
Descripción | LCD MODULE | |
Fabricantes | GEMINI | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de CGG128064GJ00-FHB-R (archivo pdf) en la parte inferior de esta página. Total 22 Páginas | ||
No Preview Available ! GEMINI TECHNOLOGY CO., LTD
RM1521 Investel, 1123-2 Sanbon-dong, Gunpo-city, Kyeongki-do, 435-040 Korea
Tel : 0082-31-455-3200
Fax : 0082-31-343-2102
E-mail: [email protected]
SPECIFICATION
FOR
LCD MODULE
MODULE NO.: CGG128064GJ00-FHB-R
Customer NO.:
REVISION: 00
GEMINI
SIGNATURE
DATE
PREPARED BY
CHECKED BY
CUSTOMER
APPROVAL
SIGNATURE
APPROVED BY
DATE
1 page GEMINI TECHNOLOGY CO., LTD
4. DIMENSIONAL OUTLINE
Figure 2. Dimensional outline
2
5 Page GEMINI TECHNOLOGY CO., LTD
12. PRECAUTION FOR USING LCD/LCM
LCD/LCM is assembled and adjusted with a high degree of precision. Do not attempt to make
any alteration or modification. The followings should be noted.
General Precautions:
1. LCD panel is made of glass. Avoid excessive mechanical shock or applying strong pressure onto
the surface of display area.
2. The polarizer used on the display surface is easily scratched and damaged. Extreme care should
be taken when handling. To clean dust or dirt off the display surface, wipe gently with cotton, or
other soft material soaked with isopropyl alcohol or ethyl alcohol, do not use water, ketone or
aromatics and never scrub hard.
3. Do not tamper in any way with the tabs on the metal frame.
4. Do not made any modification on the PCB without consulting Gemini.
5. When mounting a LCM, make sure that the PCB is not under any stress such as bending or
twisting. Elastomer contacts are very delicate and missing pixels could result from slight
dislocation of any of the elements.
6. Avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and
lose contact, resulting in missing pixels and also cause rainbow on the display.
7. Be careful not to touch or swallow liquid crystal that might leak from a damaged cell. Any liquid
crystal adheres to skin or clothes, wash it off immediately with soap and water.
Static Electricity Precautions:
1. CMOS-LSI is used for the module circuit; therefore operators should be grounded whenever
he/she comes into contact with the module.
2. Do not touch any of the conductive parts such as the LSI pads; the copper leads on the PCB and
the interface terminals with any parts of the human body.
3. Do not touch the connection terminals of the display with bare hand; it will cause disconnection
or defective insulation of terminals.
4. The modules should be kept in anti-static bags or other containers resistant to static for storage.
5. Only properly grounded soldering irons should be used.
6. If an electric screwdriver is used, it should be grounded and shielded to prevent sparks.
7. The normal static prevention measures should be observed for work clothes and working
benches.
8. Since dry air is inductive to static, a relative humidity of 50-60% is recommended.
Soldering Precautions:
1. Soldering should be performed only on the I/O terminals.
2. Use soldering irons with proper grounding and no leakage.
3. Soldering temperature:300±5℃
4. Soldering time: 2 to 3 second.
5. Use eutectic solder with resin flux filling.
6. If flux is used, the LCD surface should be protected to avoid spattering flux.
7. Flux residue should be removed.
8
11 Page |
Páginas | Total 22 Páginas | |
PDF Descargar | [ Datasheet CGG128064GJ00-FHB-R.PDF ] |
Número de pieza | Descripción | Fabricantes |
CGG128064GJ00-FHB-R | LCD MODULE | GEMINI |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |