|
|
PDF MBR4015LWTG Data sheet ( Hoja de datos )
| Número de pieza | MBR4015LWTG | |
| Descripción | Surface Mount Schottky Power Rectifier | |
| Fabricantes | ON Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de MBR4015LWTG (archivo pdf) en la parte inferior de esta página. Total 5 Páginas | ||
|
No Preview Available !
MBR4015LWTG
Switch Mode
Schottky Power Rectifier
TO247 Power Package
This device employs the Schottky Barrier principle in a large area
metal−to−silicon power rectifier. Features epitaxial construction with
oxide passivation and metal overlay contact. Ideally suited for low
voltage, high frequency switching power supplies; free wheeling
diodes and polarity protection diodes.
Features
• Highly Stable Oxide Passivated Junction
• Guardring for Overvoltage Protection
• Low Forward Voltage Drop
• Dual Diode Construction; Terminals 1 and 3 May Be Connected for
Parallel Operation at Full Rating.
• Full Electrical Isolation without Additional Hardware
• These Devices are Pb−Free, Halogen Free/BFR Free and are RoHS
Compliant*
Mechanical Characteristics
• Case: Molded Epoxy
• Epoxy Meets UL 94 V−0 @ 0.125 in
• Weight: 4.3 Grams (Approximately)
• Finish: All External Surfaces Corrosion Resistant and Terminal
Leads are Readily Solderable
• Lead and Mounting Surface Temperature for Soldering Purposes:
260°C Max. for 10 Seconds
MAXIMUM RATINGS
Rating
Symbol Value
Unit
Peak Repetitive Reverse Voltage
Working Peak Reverse Voltage
DC Blocking Voltage
VRRM
VRWM
VR
15
V
Average Rectified Forward Current
(At Rated VR, TC = 120°C)
Per Leg
Per Package
IO
A
20
40
Peak Repetitive Forward Current,
IFRM 40 A
(At Rated VR, Square Wave,
20 kHz, TC = 95°C)
Per Leg
Non−Repetitive Peak Surge Current
(Surge Applied at Rated Load
IFSM 120 A
Conditions Halfwave, Single Phase,
60 Hz) Per Package
Storage/Operating Case Temperature
Tstg, TC −55 to +150 °C
Operating Junction Temperature (Note 1)
TJ −55 to +150 °C
Voltage Rate of Change,
dv/dt
10,000 V/ms
(Rated VR, TJ = 25°C)
Stresses exceeding those listed in the Maximum Ratings table may damage the
device. If any of these limits are exceeded, device functionality should not be
assumed, damage may occur and reliability may be affected.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2014
July, 2014 − Rev. 10
1
http://onsemi.com
SCHOTTKY BARRIER
RECTIFIER
40 AMPERES, 15 VOLTS
1
2
3
1
2
3
TO−247
CASE 340AL
MARKING DIAGRAM
MBR4015LWT
AYWWG
MBR4015LWT
A
Y
WW
G
= Specific Device Code
= Assembly Location
= Year
= Work Week
= Pb−Free Package
ORDERING INFORMATION
Device
Package
Shipping
MBR4015LWTG TO−247
(Pb−Free)
30 Units / Rail
Publication Order Number:
MBR4015LWT/D
1 page  
MBR4015LWTG
PACKAGE DIMENSIONS
E2/2
NOTE 4
D
L
2X b2
NOTE 4
E
A
E2
NOTE 3
1 23
L1
NOTE 5
A
Q
c
b4
3X b
e 0.25 M B A M
TO−247
CASE 340AL
ISSUE A
B
SEATING
PLANE
A1
NOTE 7
0.635 M B A M
P NOTE 6
S
4
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETERS.
3. SLOT REQUIRED, NOTCH MAY BE ROUNDED.
4. DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH.
MOLD FLASH SHALL NOT EXCEED 0.13 PER SIDE. THESE
DIMENSIONS ARE MEASURED AT THE OUTERMOST
EXTREME OF THE PLASTIC BODY.
5. LEAD FINISH IS UNCONTROLLED IN THE REGION DEFINED BY
L1.
6. ∅P SHALL HAVE A MAXIMUM DRAFT ANGLE OF 1.5° TO THE
TOP OF THE PART WITH A MAXIMUM DIAMETER OF 3.91.
7. DIMENSION A1 TO BE MEASURED IN THE REGION DEFINED
BY L1.
MILLIMETERS
DIM MIN MAX
A 4.70 5.30
A1 2.20 2.60
b 1.00 1.40
b2 1.65 2.35
b4 2.60 3.40
c 0.40 0.80
D 20.30 21.40
E 15.50 16.25
E2 4.32 5.49
e 5.45 BSC
L 19.80 20.80
L1 3.50 4.50
P 3.55 3.65
Q 5.40 6.20
S 6.15 BSC
ON Semiconductor and the are registered trademarks of Semiconductor Components Industries, LLC (SCILLC) or its subsidiaries in the United States and/or other countries.
SCILLC owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed
at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation
or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and
specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets
and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each
customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended,
or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which
the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or
unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim
alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable
copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
http://onsemi.com
5
MBR4015LWT/D
5 Page | ||
| Páginas | Total 5 Páginas | |
| PDF Descargar | [ Datasheet MBR4015LWTG.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| MBR4015LWT | Schottky Power Rectifier | ON Semiconductor |
| MBR4015LWT | SWITCHMODE Power Rectifier |  Motorola Semiconductors |
| MBR4015LWTG | Surface Mount Schottky Power Rectifier | ON Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |