DataSheet.es    


PDF FH36-61S-0.3SHW Data sheet ( Hoja de datos )

Número de pieza FH36-61S-0.3SHW
Descripción ZIF Connectors
Fabricantes Hirose Electric 
Logotipo Hirose Electric Logotipo



Hay una vista previa y un enlace de descarga de FH36-61S-0.3SHW (archivo pdf) en la parte inferior de esta página.


Total 12 Páginas

No Preview Available ! FH36-61S-0.3SHW Hoja de datos, Descripción, Manual

0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
FH36 Series
Space saving (51 positions shown)
2.7mm
[51 Positions]
16.9mm
Features
1. Low-profile and light weight
Weight: Reduced approximately 30%
Board footprint: Reduced approximately 15%
(As compared with Hirose Electric's FH26 Series
connectors (51 positions)
2. Easy solderability on the PC board
The soldering leads are on 0.6 mm pitch, exiting on
front and back of the connector.
3. Conducive traces on the PCB can run
under the connector
No exposed contacts on the bottom of the connector.
4. Easy FPC insertion and reliable
electrical connection
Proven Flip Lock actuator allows easy insertion of
FPC and provides a tactile sensation when fully
closed, confirming complete electrical and
mechanical connection.
5. FPC position hold
Tabs on each side of the FPC assure correct
placement and hold in the connector prior to
closing of the actuator.
6. Accepts standard FPC thickness
0.2mm thick standard Flexible Printed Circuit (FPC)
can be used. This is the only ultra-low profile ZIF
connector using standard FPC.
7. Board placement with automatic
equipment
Flat upper surface and tape and reel packaging
facilitate vacuum pick-up and placement.
Standard reel packaging contains 5,000
connectors.
8. Halogen-free *
(FH36W Series)
*As defined by IEC61249-2-21
Br-900ppm maximum, Cl-900ppm maximum,
Cl + Br combined-1,500ppm maximum
Metal fittings do not protrude outside of the connector body
Can be mounted over conductive traces
No exposed contacts on the bottom of
the connector
Operation
(1) Actuator open
(2) Insert FPC
Actuator
FPC
(3) Close the actuator
(4) FPC connected
FPC temporary hold
2013.11
1

1 page




FH36-61S-0.3SHW pdf
FH36 Series0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Recommended FPC construction
Contact FPC manufacturer for specific details.
1. Using Single-sided FPC
Connecting side
Back side
Material Name
Material
Material Thickness
(μm)
Covering film layer Polyimide 1 mil thick.
(25)
Cover adhesive
(25)
Surface treatment
Copper foil
0.2μm thick gold plated over 1 to 5μm
thick nickel underplating
Cu 1oz
3
35
Base adhesive
Thermosetting adhesive
25
Base film
Polyimide 1 mil thick
25
Reinforcement material adhesive Thermosetting adhesive
40
Stiffener
Polyimide 3 mil thick
75
Total
203
2. Using Double-sided FPC
Connecting side
Back side
Material Name
Material
Material Thickness
(μm)
Covering layer film Polyimide 1 mil thick
(25)
Cover adhesive
Surface treatment
Through-hole copper
0.2μm thick gold plated over 1 to 5μm
thick nickel underplating
Cu
(25)
3
15
Copper foil
Cu 1/2oz
18
Base adhesive
Thermosetting adhesive
18
Base film
Polyimide 1 mil thick
25
Base adhesive
Thermosetting adhesive
18
Copper foil
Cover adhesive
Cu 1/2oz
Thermosetting adhesive
(18)
25
Covering film layer Polyimide 1 mil thick
25
Reinforcement material adhesive Thermosetting adhesive
25
Stiffener
Polyimide 1 mil thick
25
Total
197
* To prevent release of the FPC due to its bending, use of the double sided FPC with copper foil on the back side is NOT
RECOMMENDED.
3.Precautions
1. This specification is a recommendation for the construction of the FH36 Series FPC (t=0.2 0.03)
2. For details about the construction, please contact the FPC manufacturers.
5

5 Page





FH36-61S-0.3SHW arduino
FH36 Series0.3 mm Pitch, 1.0 mm above the board Flexible Printed Circuit ZIF Connectors
Precautions
As illustrated (Fig. 4) angle insertion may cause electrical discontinuity when the FPC is deflected in use.
Opening of the FPC pattern
Fig. 4
To avert insertion of the FPC at an angle, consideration should be given to securing enough
insertion space when designing the board lay-out. Insertion will be difficult when the FPC is too
short.
Contact FPC manufacturer for information about the bending specifications.
Verification of the fully closed actuator
The FPC should be fully inserted, with its positioning tabs fully behind the protrusions on both sides of
the connector’s insertion slot (Fig. 5).
FPC positioning tab
Protrusions FPC positioning
Fig. 5
[ Routing of the FPC (FPC fully inserted / actuator closed) ]
Do not apply any pull or upward-directed force to the FPC.
Do not make any sharp bends of FPC close to the immediate exit from the connector (Fig. 6)
Fig. 6
11

11 Page







PáginasTotal 12 Páginas
PDF Descargar[ Datasheet FH36-61S-0.3SHW.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
FH36-61S-0.3SHWZIF ConnectorsHirose Electric
Hirose Electric

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar