DataSheet.es    


PDF ST10-125T1MI Data sheet ( Hoja de datos )

Número de pieza ST10-125T1MI
Descripción Wet Tantalum Capacitors
Fabricantes Vishay 
Logotipo Vishay Logotipo



Hay una vista previa y un enlace de descarga de ST10-125T1MI (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! ST10-125T1MI Hoja de datos, Descripción, Manual

www.vishay.com
ST
Vishay
SuperTan® Wet Tantalum Capacitors
with Hermetic Seal
Vishay ST represents a major breakthrough in wet tantalum
capacitor technology. Its unique cathode system provides
the highest capacitance per unit volume. The design
facilitates a doubling of capacitance, lower ESR and higher
ripple current rating compared with conventional wet
tantalum products. Moreover, the ST has the capacitance
stability of a solid tantalum capacitor and there are no circuit
impedance restrictions.
The ST is housed in an all tantalum, hermetically sealed case
and is manufactured to withstand hazardous environments.
The ST is used widely in the defense and aerospace
industries and whenever there is a space problem.
PERFORMANCE CHARACTERISTICS
Operating Temperature: -55 °C to +85 °C
(to +125 °C with voltage derating)
Capacitance Tolerance: at 120 Hz, +25 °C.
± 20 % standard. ± 10 % available as special.
FEATURES
• Very high capacitance
• 10 μF to 1800 μF
• 25 VDC to 125 VDC
• Very low ESR
• High ripple current
• All tantalum case
• Hermetically sealed
• Low DCL
Available
Available
• Axial through-hole terminations: standard tin / lead (Sn / Pb),
100 % tin (RoHS-compliant) available
• Material categorization: for definitions of compliance
please see www.vishay.com/doc?99912
Note
* This datasheet provides information about parts that are
RoHS-compliant and / or parts that are non-RoHS-compliant. For
example, parts with lead (Pb) terminations are not RoHS-compliant.
Please see the information / tables in this datasheet for details.
APPLICATION NOTES
a. No continuous reverse voltage permissible.
b. The peak of the applied AC ripple and the applied DC
voltage must not exceed the DC voltage rating of the
capacitor.
c. Ripple current ratings by part number at 85 °C and
40 kHz are included in the table. Ripple current correction
factors for other temperatures and frequencies are given
on the next page.
d. Transient reverse voltage surges are acceptable under
the following conditions:
the peak reverse voltage does not exceed 1.5 V and the
peak current times the duration of the reverse transient
does not exceed 0.05 As. In addition, the repetition
frequency of the reverse voltage surge is less than 10 Hz.
DIMENSIONS in inches [millimeters]
Terminal welded
to case
0.250 [6.35]
MAX.
0.0253 ± 0.002 [0.64 ± 0.05] dia.
(no. 22 AWG) tinned nickel leads
solderable and weldable
0.094 [2.38]
MAX.
E
L1
E
CASE CODE
D ± 0.016 [0.41]
MAX. INSULATED
(DIA.)
T1 0.188 [4.78] 0.219 [5.56]
T2 0.281 [7.14] 0.312 [7.92]
L2 0.281 [7.14] 0.312 [7.92]
T3
0.375 [9.52]
0.406 [10.31]
T4
0.375 [9.52]
0.406 [10.31]
Notes
• Material at egress is Tantalum
• Insulation sleeving will lap over the ends of the capacitor case
“D” DIA.
L1 + 0.031 / - 0.016 [+ 0.79 / - 0.41]
UNINSULATED
0.453 [11.51]
0.641 [16.28]
1.008 [25.60]
0.766 [19.46]
1.062 [26.97]
Terminal location
within 0.031 of center
E ± 0.250 [6.3] MAX.
1.500 [38.10]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
2.250 [57.15]
• Approx. weight:
T1: 2.3 g, T2: 5.7 g,
T3: 9.4 g, T4: 14.8 g
Revision: 06-Jul-15
1 Document Number: 43000
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

1 page




ST10-125T1MI pdf
www.vishay.com
ST
Vishay
MECHANICAL CHARACTERISTICS
ITEM
CONDITION
Shock (specified pulse)
MIL-STD-202, method 213, condition I
(100 g)
Vibration, high frequency MIL-STD-202, method 204, condition D
(20 g peak)
Thermal shock
MIL-STD-202, method 107, condition A
Solderability
Terminal strength
MIL-STD-202, method 208,
ANSI/J-STD-002, test A
MIL-STD-202, method 211
Resistance to solder heat MIL-STD-202, method 210, condition C
Terminals
MIL-STD-1276
Marking
MIL-STD-1285
COMMENTS
The capacitors shall meet the requirements of MIL-PRF-39006.
The capacitors shall meet the requirements of MIL-PRF-39006.
Thermal shock shall be in accordance with MIL-PRF-39006 when
tested for 30 cycles.
Solderability shall be in accordance with MIL-PRF-39006.
Terminal strength shall be in accordance with MIL-PRF-39006.
The capacitors shall meet the requirements of MIL-PRF-39006.
Terminals shall be as specified in MIL-STD-1276. The length and
diameter of the terminals shall be as specified in Dimensions table.
All terminals shall be permanently secured internally and
externally, as applicable. All external joints shall be welded.
Marking of capacitors conforms to method I of MIL-STD-1285 and
include capacitance (in μF), capacitance tolerance letter, rated
voltage, date code, lot symbol and Vishay trademark.
SELECTOR GUIDES
Tantalum Selector Guide
Parameter Comparison Guide
www.vishay.com/doc?49054
www.vishay.com/doc?42088
Revision: 06-Jul-15
5 Document Number: 43000
For technical questions, contact: [email protected]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet ST10-125T1MI.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ST10-125T1MIWet Tantalum CapacitorsVishay
Vishay

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar