DataSheet.es    


PDF ACQ629 Data sheet ( Hoja de datos )

Número de pieza ACQ629
Descripción E-pHEMT MMIC
Fabricantes RFHIC 
Logotipo RFHIC Logotipo



Hay una vista previa y un enlace de descarga de ACQ629 (archivo pdf) en la parte inferior de esta página.


Total 6 Páginas

No Preview Available ! ACQ629 Hoja de datos, Descripción, Manual

E-pHEMT MMIC
Product Features
• Small size (4 x 4 mm)
• High gain
• High linearity
• Low cost
• Low Noise Figure
• 30dB AGC Range
• Pb-free/RoHS compliant
ACQ629
Applications
• FTTH (G-PON, GE-PON)
• Optical node
• RFoG
Package Type : QFN4X4
Description
ACQ629 is designed as low cost Trans-impedance amplifiers for many applications including FTTH, RFoG, Optical, Triplexers.
This MMIC is based on Gallium Arsenide Enhancement Mode pHEMT which shows low current draw and very low noise.
The data in this spec sheet is valid only for 75ohm RF Video output application.
Electrical Specifications
PARAMETER
Frequency
Gain
Gain Flatness
Input Return Loss
Output Return Loss
Output IP3
1dB Compression Point
Noise Figure
UNIT
MHz
dB
dB
dB
dB
dBm
dBm
dB
MIN
50
-
-
-
-
30
19
-
TYP
-
37.5
1
-15
-12
36
22
2
AGC Range
π Pin Diode (SMP1307-027)
dB
-
30
CSO
dBc -
-60
CTB
50 ~ 870MHz
dBc
-
-65
XMOD
dBc -
-60
CSO
dBc -
-70
CTB
50 ~ 870MHz
dBc
-
-80
XMOD
dBc -
-75
ACQ629 DC Current
mA -
130
AGC DC Current
mA -
30
Note
1. Test conditions unless otherwise noted. Test Freq = 500MHz, T=25, VDD=5V, 75Ω system
2. OIP3 measured with 2 tones at an output power of +5dBm/tone separated by 1MHz
MAX
1000
-
-
-10
-8
-
-
4
-
-55
-60
-55
-65
-75
-70
-
-
CONDITION
-
ACQ629 + AGC
Insertion Loss 2dB
AGC Vctr = 10.0V
Vctr = 0V ~ 10V
135 channel FLAT
+30dBmV/ch
135 channel FLAT
+20dBmV/ch
VDD = +12.0V
AGC Vctr = 10.0V
Korean Facilities : 82-31-8069-3036 / [email protected]
US Facility : 919-677-8780 / [email protected]
1/6
All specifications may change without notice
Version 1.1

1 page




ACQ629 pdf
E-pHEMT MMIC
ACQ629
Package Dimension (Type: QFN4x4)
* Unit: mm[inch] | Tolerance ±0.2[.008]
Top View
Side View
Bottom View
Pin Description
Pin No Function Pin No Function Pin No Function Pin No Function
1 AMP1_IN 6 AMP2_Source 11 AMP4_OUT 16
N/C
2 AMP1_Source 7
AMP2_OUT 12 AMP4_OUT 17
AMP3_IN
3
N/C
8
AMP4_IN
13
N/C
18 AMP3_IN
4 AMP2_Source 9
AMP4_IN
14 AMP3_OUT 19 AMP1_OUT
5
AMP2_IN
10
N/C
15 AMP3_OUT 20 AMP1_Source
*N/C: Not Connected
* Mounting Configuration Notes
1. Ground / thermal via holes are critical for the proper performance of this device.
2. Add as much copper as possible to inner and outer layers near the part to ensure optimal thermal performance.
3. Mounting screws can be added near the part to fasten the board to a heatsink. Ensure that the ground / thermal via hole region contacts the heatsink.
4. Do not put solder mask on the backside of the PCB in the region where the board contacts the heatsink.
5. RF trace width depends upon the PCB material and construction.
6. Use 1 oz. Copper minimum.
Korean Facilities : 82-31-8069-3036 / [email protected]
US Facility : 919-677-8780 / [email protected]
5/6
All specifications may change without notice
Version 1.1

5 Page










PáginasTotal 6 Páginas
PDF Descargar[ Datasheet ACQ629.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
ACQ624E-pHEMT MMICRFHIC
RFHIC
ACQ629E-pHEMT MMICRFHIC
RFHIC

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar