DataSheet.es    


PDF FM8PE59 Data sheet ( Hoja de datos )

Número de pieza FM8PE59
Descripción EPROM/ROM-Based 8-Bit Microcontroller
Fabricantes Feeling Technology 
Logotipo Feeling Technology Logotipo



Hay una vista previa y un enlace de descarga de FM8PE59 (archivo pdf) en la parte inferior de esta página.


Total 30 Páginas

No Preview Available ! FM8PE59 Hoja de datos, Descripción, Manual

FEELING
TECHNOLOGY
FM8PE59
EPROM/ROM-Based 8-Bit Microcontroller
Devices Included in this Data Sheet:
FM8PE59AE : 28-pin EPROM device
FM8PE59BE : 32-pin EPROM device
FM8PE59A : 28-pin Mask ROM device
FM8PE59B : 32-pin Mask ROM device
FEATURES
Only 49 single word instructions
All instructions are single cycle except for program branches which are two-cycle
13-bit wide instructions
All ROM/EPROM area GOTO/FGOTO instruction
All ROM/EPROM area subroutine CALL/FCALL instruction
8-bit wide data path
5-level deep hardware stack
4K x 13 bits on chip EPROM/ROM
144 x 8 bits on chip general purpose registers (SRAM)
Operating speed: DC-20 MHz clock input
DC-100 ns instruction cycle
Direct, indirect addressing modes for data accessing
One 8-bit real time clock/counter (Timer0) with 8-bit programmable prescaler
One 8-bit real time clock/counter (Timer1) with 2-bit programmable prescaler and period setting
Internal Power-on Reset (POR)
Built-in Low Voltage Detector (LVD) for Brown-out Reset (BOR)
Power-up Reset Timer (PWRT) and Oscillator Start-up Timer(OST)
On chip Watchdog Timer (WDT) with internal oscillator for reliable operation and soft-ware watch-dog
enable/disable control
Three I/O ports IOA, IOB and IOC with independent direction control
16 soft-ware control pull-high pins: Port B/Port C
8 soft-ware control pull-down pins:IOA0~A3/IOB0~B3
2 soft-ware control open-drain pins: IOC6/IOC7
IR output channel with programmable frequency and duty cycle
Serial Peripheral Interface (SPI)
Four internal interrupt source: Timer0 overflow, Timer1 match, IROUT, and SPI module; Two external interrupt
source: INT0 pin, and INT1 pin
Wake-up from SLEEP by Port B/IOC4/IOC5 input falling
Power saving SLEEP mode
Programmable Code Protection
Selectable oscillator options:
- ERC: External Resistor/Capacitor Oscillator
- XT: Crystal/Resonator Oscillator
- HF: High Frequency Crystal/Resonator Oscillator
- LF: Low Frequency Crystal Oscillator
- IRC: Internal Resistor/Capacitor Oscillator
Wide-operating voltage range:
- EPROM : 2.3V to 5.5V
- ROM : 2.3V to 5.5V
This datasheet contains new product information. Feeling Technology reserves the rights to modify the product specification without notice.
No liability is assumed as a result of the use of this product. No rights under any patent accompany the sales of the product.
Rev1.5 May 21, 2010
P.1/FM8PE59

1 page




FM8PE59 pdf
FEELING
TECHNOLOGY
FM8PE59
1.0 MEMORY ORGANIZATION
FM8PE59 series memory is organized into program memory and data memory.
1.1 Program Memory Organization
The FM8PE59 series have an 12-bit Program Counter capable of addressing a 4K×13 program memory space.
The RESET vector for the FM8PE59 series is at FFFh.
The H/W interrupt vector is at 008h. And the S/W interrupt vector is at 002h.
FM8PE59 series has program memory size greater than 1K words, but the CALL and GOTO instructions only have
a 10-bit address range. This 10-bit address range allows a branch within a 1K program memory page size. To allow
CALL and GOTO instructions to address the entire 4K program memory address range for FM8PE59 series, there is
another two bits to specify the program memory page. This paging bit comes from the PCHBUF<3:2> bits. When
doing a CALL or GOTO instruction, the user must ensure that page bit PCHBUF<3:2> are programmed so that the
desired program memory page is addressed. When one of the return instructions is executed, the entire 12-bit PC is
POPed from the stack. Therefore, manipulation of the PCHBUF <3:2> is not required for the return instructions.
User can use “PAGE” instruction to change memory page and maintains the program memory page. Otherwise,
user can use “FCALL(far call)/FGOTO(far goto)” instructions to program user's code.
FIGURE 1.1: Program Memory Map and STACK
PC<11:0>
FFFh
Stack 1
Stack 2
Stack 3
Stack 4
Stack 5
Reset Vector
:
:
008h H/W Interrupt Vector
002h S/W Interrupt Vector
000h
FM8PE59 Series
Rev1.5 May 21, 2010
P.5/FM8PE59

5 Page





FM8PE59 arduino
FEELING
TECHNOLOGY
FM8PE59
Situation 5: RETIA, RETFIE, or RETURN Instruction
PCH
11 10 9 8 7
PC
PCL
0
STACK<11:0>
----
PCHBUF
Situation 6: Instruction with PCL as destination (except TBL instruction)
PCH
11 10 9 8 7
PC
PCL
PCHBUF<3:0>
0
----
PCHBUF
ALU result<7:0>
or Opcode<7:0>
Situation 7: TBL Instruction
PCH
11 10 9 8 7
PC
PCHBUF<3:2>
PCL
----
PCHBUF
0
ALU result<7:0>
PCH<9:8> bits are unchanged
Note: PCHBUF is used for instruction with PCL as destination, GOTO and CALL instructions.
Rev1.5 May 21, 2010
P.11/FM8PE59

11 Page







PáginasTotal 30 Páginas
PDF Descargar[ Datasheet FM8PE59.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
FM8PE51EPROM/ROM-Based 8-Bit MicrocontrollerFeeling Technology
Feeling Technology
FM8PE53BOTP-Based 8-Bit MicrocontrollerFeeling Technology
Feeling Technology
FM8PE54EPROM/ROM-Based 8-Bit MicrocontrollerFeeling Technology
Feeling Technology
FM8PE54EEPROM/ROM-Based 8-Bit MicrocontrollerFeeling Technology
Feeling Technology

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar