|
|
PDF RJU002N06FRA Data sheet ( Hoja de datos )
| Número de pieza | RJU002N06FRA | |
| Descripción | MOSFET ( Transistor ) | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de RJU002N06FRA (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
2.5V Drive Nch MOSFET
RRJJUU002N06FRA
AEC-Q101 Qualified
zStructure
Silicon N-channel MOS FET
zFeatures
1) Low On-resistance.
2) Low voltage drive (2.5V drive).
zApplications
Switching
zPackaging specifications
Package
Type
Code
Basic ordering unit (pieces)
RRJJUU000022NN0066FRA
Taping
T106
3000
zDimensions (Unit : mm)
UMT3
2.0
0.3
(3)
0.9
0.2 0.7
(1) Source
(2) Gate
(3) Drain
(2) (1)
0.65 0.65
1.3
0.15
Each lead has same dimensions
Abbreviated symbol : ML
zInner circuit
(3)
(2) ∗2
∗1
∗1 ESD PROTECTION DIODE (1)
∗2 BODY DIODE
zAbsolute maximum ratings (Ta=25°C)
Parameter
Drain-source voltage
Gate-source voltage
Drain current
Continuous
Pulsed
Total power dissipation
Channel temperature
Range of storage temperature
∗1 Pw≤10µs, Duty cycle≤1%
∗2 Each terminal mounted on a recommended land
Symbol
VDSS
VGSS
ID
IDP ∗1
PD ∗2
Tch
Tstg
Limits
60
±12
±200
±800
200
150
−55 to +150
Unit
V
V
mA
mA
mW
°C
°C
zThermal resistance
Parameter
Channel to ambient
∗ Each terminal mounted on a recommended land
Symbol
Rth(ch-a) ∗
Limits
625
Unit
°C/W
(1) Source
(2) Gate
(3) Drain
www.rohm.com
○c 2009 ROHM Co., Ltd. All rights reserved.
1/4
2016.05 - Rev.B
1 page  
Datasheet
Notice
Precaution on using ROHM Products
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1),
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU CHINA
CLASSⅢ
CLASSⅣ
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
© 2015 ROHM Co., Ltd. All rights reserved.
Rev.001
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet RJU002N06FRA.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| RJU002N06FRA | MOSFET ( Transistor ) | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |