|
|
Número de pieza | LB043WV2-SD01 | |
Descripción | Display Module | |
Fabricantes | LG | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de LB043WV2-SD01 (archivo pdf) en la parte inferior de esta página. Total 30 Páginas | ||
No Preview Available ! Product Specification
LB043WV2-SD01
Liquid Crystal Display
SPECIFICATION
FOR
APPROVAL
(●) Preliminary Specification
( ) Final Specification
Title
BUYER
MODEL
LB043WV2-SD01
SUPPLIER
MODEL
SUFFIX
LG Display Co., Ltd.
LB043WV2
SD01
SIGNATURE
/
/
/
DATE
APPROVED BY
DATE
REVIEWED BY
PREPARED BY
Please return 1 copy for your confirmation
With your signature and comments.
Product Engineering Dept.
LG Display Co., Ltd
Ver 3.0
November. 17. 2016
1 / 52
www.avnet-embedded.eu
1 page Product Specification
LB043WV2-SD01
Liquid Crystal Display
3. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause operation or damage to the unit.
Item
Symbol
Min.
Typ.
Max.
Unit Remark
Power for Analogue Circuit
Power for Logic Circuit
LED Forward Current
LED Reverse Voltage
LED Permissible Loss
Storage Humidity
Storage Temperature
Operating Ambient Humidity
Operating Ambient
Temperature
Vcc
IOVcc
IF
VR
PD
Hstg
TSTG
HOP
TOP
-0.3
-0.3
-
-
-
10
-30
10
-20
2.8 3.3 V VCC
1.8 3.3
V IOVCC
20 25 mA Per LED
- 5 V Per LED
- 120 mW Per LED
- 90 %RH Note 1), 2)
- 80 °C Note 1), 2)
- 90 %RH Note 1), 2)
- 70 °C Note 1), 2)
Note 1) Temp. ≤ 60℃ , 90% RH MAX.
Temp. >60℃ , Absolute humidity shall be less than 90% RH at 60℃.
Note 2) The diagram below indicates the peripheral environment of the module.
The wet bulb temperature should be kept under 39 °C and there should be no compensation.
If the LSI is used above these absolute maximum ratings, it may become permanently damaged.
95%80%
Wet Bulb
Temperature [℃]
60
50
60%
Humidity
[(%)RH]
40
30
20
10
0
40%
20%
10%
Storage
Operation
-30 -20
0 10 20 30 40 50 60 70 80
Dry Bulb Temperature [℃]
Ver 3.0
November. 17. 2016
5 / 52
www.avnet-embedded.eu
5 Page Product Specification
LB043WV2-SD01
Liquid Crystal Display
◈ Measurement System
Notes :
1. Contrast Ratio(CR) is defined mathematically as :
Surface Luminance with all white pixels
Contrast Ratio = ----------------------------------------------------------
Surface Luminance with all black pixels
2. Surface luminance is the center point across the LCD surface 500mm from the surface with all
pixels displaying white. For more information see FIG 1.
3. Response time is the time required for the display to transition from white to black (Rising Time, Tr)
and from black to white (Falling Time, Tf). For additional information see FIG 3.
4. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are
determined for the horizontal or x axis and the vertical or y axis with respect to the z axis which
is normal to the LCD surface. For more information see FIG 4.
FIG. 1 Optical Characteristic Measurement Equipment and Method
▶ Test procedure
Optical Stage(x,y)
LCD Module
Pritchard 880/650
or Equivalent
0.5′
50cm
※ Measuring Condition:
• Measuring surroundings : Dark Room
• Measuring temperature : Ta=25oC
• Adjust operating voltage to get optimum contrast at the center of the display.
• Measured value at the center point of LCD panel after more than 5 minutes while backlight turning on.
Ver 3.0
November. 17. 2016
11 / 52
www.avnet-embedded.eu
11 Page |
Páginas | Total 30 Páginas | |
PDF Descargar | [ Datasheet LB043WV2-SD01.PDF ] |
Número de pieza | Descripción | Fabricantes |
LB043WV2-SD01 | Display Module | LG |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |