DataSheet.es    


PDF TOP222YN Data sheet ( Hoja de datos )

Número de pieza TOP222YN
Descripción Three-Terminal Off-Line PWM Switch
Fabricantes Power Integrations 
Logotipo Power Integrations Logotipo



Hay una vista previa y un enlace de descarga de TOP222YN (archivo pdf) en la parte inferior de esta página.


Total 20 Páginas

No Preview Available ! TOP222YN Hoja de datos, Descripción, Manual

This product is not recommended for new designs.
TOP221-227
TOPSwitch-II Family
Three-Terminal Off-Line PWM Switch
Product Highlights
• Lowest cost, lowest component count switcher solution
• Cost competitive with linears above 5 W
• Very low AC/DC losses – up to 90% efficiency
• Built-in Auto-restart and Current limiting
• Latching Thermal shutdown for system level protection
• Implements Flyback, Forward, Boost or Buck topology
• Works with primary or opto feedback
• Stable in discontinuous or continuous conduction mode
• Source connected tab for low EMI
• Circuit simplicity and Design Tools reduce time to market
Description
The second generation TOPSwitch-II family is more cost
effective and provides several enhancements over the first
generation TOPSwitch family. The TOPSwitch-II family
extends the power range from 100W to 150W for 100/115/
230 VAC input and from 50W to 90W for 85-265 VAC univer-
sal input. This brings TOPSwitch technology advantages
to many new applications, i.e. TV, Monitor, Audio amplifiers,
etc. Many significant circuit enhancements that reduce the
sensitivity to board layout and line transients now make the
design even easier. The standard 8L PDIP package option
AC
IN
D
TOPSwitch
CONTROL C
S
Figure 1. Typical Flyback Application.
PI-1951-091996
reduces cost in lower power, high efficiency applications.
The internal lead frame of this package uses six of its pins to
transfer heat from the chip directly to the board, eliminating
the cost of a heat sink. TOPSwitch incorporates all functions
necessary for a switched mode control system into a three
terminal monolithic IC: power MOSFET, PWM controller, high
voltage start up circuit, loop compensation and fault protec-
tion circuitry.
Output Power Table
TO-220 (Y) Package1
PART
ORDER
NUMBER
Single Voltage Input 3
100/115/230 VAC ±15%
P 4,6
MAX
Wide Range Input
85 to 265 VAC
P 4,6
MAX
TOP221YN
12 W
7W
TOP222YN
25 W
15 W
8L PDIP (P) or 8L SMD (G) Package2
PART
ORDER
NUMBER
Single Voltage Input3
100/115/230 VAC ±15%
P 5,6
MAX
Wide Range Input
85 to 265 VAC
P 5,6
MAX
TOP221 PN or TOP221GN
9W
6W
TOP222 PN or TOP222GN
15 W
10 W
TOP223YN
50 W
30 W
TOP223 PN or TOP223GN
25 W
15 W
TOP224YN
75 W
45 W
TOP224 PN or TOP224GN
30 W
20 W
TOP225YN
100 W
60 W
TOP226YN
125 W
75 W
TOP227YN
150 W
90 W
Notes: 1. Package outline: TO-220/3 2. Package Outline: DIP-8 or SMD-8 3. 100/115 VAC with doubler input 4. Assumes appro-
priate heat sinking to keep the maximum TOPSwitch junction temperature below 100 °C. 5. Soldered to 1 sq. in. (6.45 cm2), 2 oz.
cpoopwpeer rccalpaadb(i6lit1y0ingma /gmiv2)en6a. pPpMAliXciastitohne
maximum practical continuous power output level for conditions
depends on thermal environment, transformer design, efficiency
shown. The continuous
required, minimum spec-
ified input voltage, input storage capacitance, etc. 7. Refer to key application considerations section when using TOPSwitch-II in
an existing TOPSwitch design.
www.power.com
This Product is Covered by Patents and/or Pending Patent Applications.
August 2016

1 page




TOP222YN pdf
VIN
VIN
DRAIN
0
VOUT
0
IOUT
0
VC
0
IC 0
•••
•••
•••
•••
TOP221-227
VC(reset)
Figure 6. Typical Waveforms for (1) Normal Operation, (2) Auto-restart, and (3) Power Down Reset.
The leading edge blanking circuit inhibits the current limit
comparator for a short time after the output MOSFET is
turned on. The leading edge blanking time has been set so
that current spikes caused by primary-side capacitances
and secondary-side rectifier reverse recovery time will not
cause premature termination of the switching pulse.
The current limit can be lower for a short period after the
leading edge blanking time as shown in Figure 12. This is
due to dynamic characteristics of the MOSFET. To avoid trig-
gering the current limit in normal operation, the drain current
waveform should stay within the envelope shown.
Shutdown/Auto-restart
To minimize TOPSwitch power dissipation, the shutdown/
auto-restart circuit turns the power supply on and off at an
auto-restart duty cycle of typically 5% if an out of regulation
condition persists. Loss of regulation interrupts the external
schuurrnetnmt iondtoetthoethCeOhNyTsRteOreLtipcina.uVtoC-rreegstualrattimonodcehadnegsecsribfreodm
above. When the fault condition is removed, the power sup-
ply output becomes regulated,
mode, and normal operation of
VthCerepgouwlaetriosnupreptluyrnresstuomsehsu.nt
Overtemperature Protection
Temperature protection is provided by a precision analog
circuit that turns the output MOSFET off when the junction
temperature exceeds the thermal shutdown temperature
(typically 135 °C). Activating the power-up reset circuit by
removing and restoring input power or momentarily pulling
the CONTROL pin below the power-up reset threshold resets
the latch and allows TOPSwitch to resume normal power
s4u.7ppVlytoo5p.e7raVti(otynp. icVaCl)issarewgtuoloatthedwainvehfyosrtmereisticprmesoednet
and a
on the
CONTROL pin when the power supply is latched off.
High-Voltage Bias Current Source
This current source biases TOPSwitch from the DRAIN pin
and charges the CONTROL
during start-up or hysteretic
oppineeraxttieornn.alHcyasptearceittiacnocpee(rCaT-)
tion occurs during auto-restart and overtemperature latched
shutdown. The current source is switched on and off with an
effective duty cycle of approximately 35%. This duty cycle
dtisuisrdnceehtdaerrogmfefindceuudrrirnbegyntntshoe(rImCrDaa1tliaoonpodef IrCCaDOt2io)N.nTTRwhOhiseLncputihrnreecnohtuastrpoguuetrc(MIeCO)isaSnFdET
is switching.
www.power.com
5
Rev. G 08/16

5 Page





TOP222YN arduino
TOP221-227
Conditions
Paramet er Sy mbol
(Unless Otherwise Specified)
See Figure 14 Min Typ M ax Unit s
SOURCE = 0 V; TJ = -40 to 125 °C
SHUTDOWN/AUTO-RESTART (cont.)
Auto-restart
Threshold Voltage
S1 open
5.7
V
UV Lockout
Threshold Voltage
S1 open
4.4 4.7 5.0
V
Auto-restart
Hysteresis Voltage
Auto-restart
Duty Cycle
Auto-restart
Frequency
S1 open
0.6 1.0 V
S1 open
TOP221-222 2 5 9
TOP223-227 2 5 8
%
S1 open
1.2
Hz
CIRCUIT PROTECTION
di/dt = 40 mA/µs,
TJ = 25 °C
TOP221YN
TOP221PN or GN 0.23 0.25 0.28
di/dt = 80 mA/µs,
TOP222YN
0.45 0.50 0.55
TJ = 25 °C
di/dt = 160 mA/µs,
TOP222PN or GN
TOP223YN
TJ = 25 °C
TOP223PN or GN 0.90 1.00 1.10
Self-protection
Current Limit
ILIMIT
di/dt = 240 mA/µs, TOP224YN
TJ = 25 °C
TOP224PN or GN 1.35 1.50 1.65
A
di/dt = 320 mA/µs,
TOP225YN
TJ = 25 °C
di/dt = 400 mA/µs,
TOP226YN
TJ = 25 °C
1.80 2.00 2.20
2.25 2.50 2.75
di/dt = 480 mA/µs,
TOP227YN
TJ = 25 °C
85 VAC
2.70 3.00 3.30
0.75 x
Initial Current Limit
IINIT
See Figure 12 (Rectifi ed Line Input) ILIMIT(MIN)
TJ = 25 °C
265 VAC
0.6 x
(Rectified Line Input) ILIMIT (MIN)
A
Leading Edge
Blanking Time
tLEB
IC = 4 mA,
TJ = 25 °C
180
ns
www.power.com
11
Rev. G 08/16

11 Page







PáginasTotal 20 Páginas
PDF Descargar[ Datasheet TOP222YN.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
TOP222YThree-terminal Off-line PWM SwitchPower Integrations  Inc.
Power Integrations Inc.
TOP222YNThree-Terminal Off-Line PWM SwitchPower Integrations
Power Integrations

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar