DataSheet.es    


PDF BH31M0AWHFV Data sheet ( Hoja de datos )

Número de pieza BH31M0AWHFV
Descripción 1ch 300mA CMOS LDO Regulators
Fabricantes ROHM Semiconductor 
Logotipo ROHM Semiconductor Logotipo



Hay una vista previa y un enlace de descarga de BH31M0AWHFV (archivo pdf) en la parte inferior de esta página.


Total 13 Páginas

No Preview Available ! BH31M0AWHFV Hoja de datos, Descripción, Manual

Datasheet
CMOS LDO Regulators for Portable Equipments
1ch 300mA
CMOS LDO Regulators
BHxxM0A series
General Description
BHxxM0A series are high-performance CMOS LDO
regulators with output current ability of up to 300mA. These
devices have excellent noise characteristics despite of
their low circuit current consumption of 65µA. They are
most appropriate for various applications such as power
supplies for logic IC, RF, and camera modules.
Features
„ High Output Voltage Accuracy: ±1 %
(±25mV on VOUT<2.5V products)
„ Dropout voltage: 60mV (IOUT=100mA)
„ Compatible with small ceramic capacitor
„ Output Voltage ON/OFF Control
„ Built-in Over Current Protection Circuit (OCP)
„ Built-in Thermal Shutdown Circuit (TSD)
„ Ultra-small power package:HVSOF6
Applications
„ Battery-driven portable devices
„ Other electronic devices using microcontrollers or
logic circuits
Key Specifications
„ Input Power Supply Voltage Range:
„ Output Current Range:
„ Operating Temperature Range:
„ Output Voltage Lineup:
„ Output Voltage Accuracy:
„ Circuit Current:
„ Standby Current:
2.5V to 5.5V
0 to 300mA
-40 to 85
1.5V to 3.4V
±1%
65μA (Typ.)
0μA (Typ.)
Package
HVSOF6
W(Typ.) x D(Typ.) x H(Max.)
1.60mm x 3.00mm x 0.75mm
Typical Application Circuit
Vin
Cin
On
Off
VIN VOUT
VOUT
BHxxM0A
STBY
GND
NOISE
Figure 1. Typical Application Circuit
Vout
Cout
Cn
Product structureSilicon monolithic integrated circuit
.www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ2211114001
This product is not designed protection against radioactive rays
1/10
TSZ02201-0RBR0A300070-1-2
21.Nov.2013 Rev.001

1 page




BH31M0AWHFV pdf
BHxxM0A series
Reference data BH30M0AWHFV (Unless otherwise specified, Ta=25.)
Datasheet
Figure 3. Output Voltage vs. Input Voltage
Figure 4. GND Current vs. Input Voltage
Figure 5. Output Voltage vs. Output Current
(OCP Threshold)
Figure 6. Dropout Voltage vs. Output Current
www.rohm.com
© 2012 ROHM Co., Ltd. All rights reserved.
TSZ2211115001
5/10
TSZ02201-0RBR0A300070-1-2
21.Nov.2013 Rev.001

5 Page





BH31M0AWHFV arduino
Datasheet
Notice
General Precaution
1) Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2) All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
Precaution on using ROHM Products
1) Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment, transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
2) ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3) Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4) The Products are not subject to radiation-proof design.
5) Please verify and confirm characteristics of the final or mounted products in using the Products.
6) In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse) is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7) De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8) Confirm that operation temperature is within the specified range described in the product specification.
9) ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Notice - Rev.004
© 2013 ROHM Co., Ltd. All rights reserved.

11 Page







PáginasTotal 13 Páginas
PDF Descargar[ Datasheet BH31M0AWHFV.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
BH31M0AWHFV1ch 300mA CMOS LDO RegulatorsROHM Semiconductor
ROHM Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar