|
|
PDF BD11600NUX Data sheet ( Hoja de datos )
| Número de pieza | BD11600NUX | |
| Descripción | USB Switch IC | |
| Fabricantes | ROHM Semiconductor | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de BD11600NUX (archivo pdf) en la parte inferior de esta página. Total 13 Páginas | ||
|
No Preview Available !
USB Switch ICs
DPDT Type
(Double Pole Double Throw)
BD11600NUX
No.11103EAT03
●Description
BD11600NUX is DPDT analog switches handling with USB2.0 high-speed that have both a low resistance and a low
capacitance. Moreover, this is widely guaranteed from 2.5V to 5.5V as for the range of the power-supply voltage.
This has a low consumption mode by making OE “H” and the multi-selector by making the combination of OE “L” and S.
The electrostatic discharge protection circuit is built-in in all terminals.
●Features
1) VCC Operation from 2.5V to 5.5V.
2) 3Ω switches between the input to the output.
3) Low Capacity 2ch Analog SW.
4) 10-Pin SON Package. (3.0mm x 2.0mm, Height=0.6mm, 0.5mm pitch)
●Applications
Digital Still Cameras, Digital Video Camcorders, Portable Navigation Devices, TV, Portable DVD Players,
Portable Game Systems, Personal computers, PDA, Mobile phones
●Line up matrix
Parameter
BD11600NUX
BD11601NUX
Supply Quiescent Current
Input voltage range
Switch ON Resistance ( VIN=0 V )
Switch ON Capacitance
Configuration
Package
3Ω
DPDT
VSON010X3020
18 µA
2.5～5.5 V
6 pF
2.5 Ω
DPST
VSON008X2020
●Absolute maximum ratings (Ta=25℃)
Parameter
Symbol
Ratings
Unit Conditions
Input supply voltage
Vmax
-0.5～7.0
V D+,D-,1D+,1D-,2D+,2D- Pins
Input supply voltage
Vmax
-0.3～7.0
V Other Pins
Power dissipation
Pd
1.925
W *1
Operating temperature range
Topr
-40～+85
℃
Storage temperature range
Tstr
-55～+150
℃
*1 When using more than at Ta=25℃, it is reduced 15.4 mW per 1℃. ROHM specification board 70mm×70mm mounting.
●Operating conditions (Ta=-40～+85℃)
Parameter
Symbol
Ratings
Unit Conditions
Input voltage range (VCC)
VCC
2.5～5.5
* This product does not especially designed to be protected from radioactivity.
V
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
1/10
2011.08 - Rev.A
1 page  
BD11600NUX
●Pin Description
Pin NO.
1
2
3
4
5
6
7
8
9
10
Terminal
circuit
A
B
C
D
-
E
F
G
H
-
Pin Name
1D+
1D-
2D+
2D-
GND
OE
D-
D+
S
VCC
I／O
O
O
O
O
-
I
I
I
I
-
Function
Analog SW terminal.
Ground Pin.
Bus-Switch Analog Pin.
Analog SW terminal.
Select Input Pin.
Power Supply.
●Truth Table
OE
S
SW1
SW2
H
L
OFF
OFF
Signal Pass
ALL OFF
H
H
OFF
OFF
ALL OFF
L L ON OFF 1D+⇔D+, 1D-⇔D-
L
H
OFF
ON
2D+⇔D+, 2D-⇔D-
●Equivalent Circuit
A,B,C,D
F,G
Technical Note
PIN PIN
E,H
VCC
PIN
www.rohm.com
© 2011 ROHM Co., Ltd. All rights reserved.
5/10
2011.08 - Rev.A
5 Page 
Datasheet
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU CHINA
CLASSⅢ
CLASSⅣ
CLASSⅢ
CLASSⅡb
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
© 2014 ROHM Co., Ltd. All rights reserved.
Rev.002
11 Page | ||
| Páginas | Total 13 Páginas | |
| PDF Descargar | [ Datasheet BD11600NUX.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| BD11600NUX | USB Switch IC | ROHM Semiconductor |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |