DataSheet.es    

PDF ASM3P2775A Data sheet ( Hoja de datos )

Número de pieza ASM3P2775A
Descripción Low Power Peak EMI Reducing Solution
Fabricantes PulseCore Semiconductor 
Logotipo PulseCore Semiconductor Logotipo



Total 10 Páginas
		
ASM3P2775A Hoja de datos, Descripción, Manual
November 2006
rev 0.3
Low Power Peak EMI Reducing Solution
ASM3P2775A
Features
Generates an EMI optimized clock signal at the
output.
Integrated loop filter components.
Operates with a 3.3V Supply.
Operating current less than 4mA.
Low power CMOS design.
Input frequency range: 13MHz to 30MHz
Generates a 1X low EMI spread spectrum clock
of the input frequency.
Frequency deviation: ±1.75% (Typ) @14.7MHz
Input Frequency.
Available in 6-pin TSOT-23, 8-pin SOIC and 8-
pin TSSOP packages.
Product Description
The ASM3P2775A is a versatile spread spectrum
frequency modulator designed specifically for a wide
range of clock frequencies. The ASM3P2775A reduces
electromagnetic interference (EMI) at the clock source,
allowing system wide reduction of EMI of all clock
dependent signals. The ASM3P2775A allows significant
system cost savings by reducing the number of circuit
board layers, ferrite beads and shielding that are
traditionally required to pass EMI regulations.
The ASM3P2775A uses the most efficient and optimized
modulation profile approved by the FCC and is
implemented by using a proprietary all digital method.
The ASM3P2775A modulates the output of a single PLL
in order to “spread” the bandwidth of a synthesized clock,
and more importantly, decreases the peak amplitudes of
its harmonics. This results in significantly lower system
EMI compared to the typical narrow band signal produced
by oscillators and most frequency generators. Lowering
EMI by increasing a signal’s bandwidth is called ‘spread
spectrum clock generation’.
Applications
The ASM3P2775A is targeted towards all portable
devices with very low power requirements like MP3
players and digital still cameras.
Key Specifications
Description
Supply voltages
Cycle-to-Cycle Jitter
Output Duty Cycle
Modulation Rate Equation
Frequency Deviation
Specification
VDD = 3.3V ± 0.3V
200pS (Max)
45/55% (worst case)
FIN/640
±1.75% (Typ) @ 14.7MHz
Block Diagram
VDD
PD
XIN/CLKIN
XOUT
Crystal
Oscillator
Frequency
Divider
Feedback
Divider
Modulation
Phase
Detector
Loop
Filter
PLL
VCO
Output
Divider
ModOUT
VSS
PulseCore Semiconductor Corporation
1715 S. Bascom Ave Suite 200 Campbell, CA 95008 Tel: 408-879-9077 Fax: 408-879-9018
www.pulsecoresemi.com
Notice: The information in this document is subject to change without notice.

1 page

ASM3P2775A pdf
November 2006
rev 0.3
Typical Crystal Oscillator Circuit
ASM3P2775A
Crystal
R1 = 510
C1 = 27 pF
C2 = 27 pF
Typical Crystal Specifications
Fundamental AT cut parallel resonant crystal
Nominal frequency
Frequency tolerance
Operating temperature range
Storage temperature
Load capacitance
Shunt capacitance
ESR
14.31818MHz
± 50 ppm or better at 25°C
-25°C to +85°C
-40°C to +85°C
18pF
7pF maximum
25
Low Power Peak EMI Reducing Solution
Notice: The information in this document is subject to change without notice.
5 of 10

5 Page



PáginasTotal 10 Páginas
PDF Descargar[ Datasheet ASM3P2775A.PDF ]

Enlace url


Hoja de datos destacado

Número de piezaDescripciónFabricantes
ASM3P2775ALow Power Peak EMI Reducing SolutionPulseCore Semiconductor
PulseCore Semiconductor
ASM3P2775ALow Power Peak EMI Reducing SolutionON Semiconductor
ON Semiconductor

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


www.DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar