|
|
PDF ICE1HS01G-1 Data sheet ( Hoja de datos )
| Número de pieza | ICE1HS01G-1 | |
| Descripción | Half-Bridge Resonant Controller | |
| Fabricantes | Infineon | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de ICE1HS01G-1 (archivo pdf) en la parte inferior de esta página. Total 19 Páginas | ||
|
No Preview Available !
Datasheet, Version 2.0, 04 July 2011
Power Management & Supply
Never stop thinking.
1 page  
Half-Bridge Resonant Controller
ICE1HS01G-1
Pin Configuration and Functionality
1 Pin Configuration and switching frequency and the switching frequency
Functionality
during soft start are also related to the current flowing
out of FMIN pin.
1.1 Pin configuration with PG-DSO-8
Pin Symbol Function
1 FMIN Minimum switching frequency
2 CS
Current sense
3 FB
Feedback voltage
4 VINS Input voltage sense
5 GND IC ground
6 LG
Low side gate drive
7 HG
High side gate drive
8 VCC IC power supply
FMIN
1
8 VCC
CS (current sense)
The current sense signal is fed to this pin. Inside the IC,
two comparators are provided. If the voltage on CS pin
is higher than the first threshold, IC will increase the
switching frequency to limit the maximum output power
of the converter. If the voltage on this pin exceeds the
second threshold, IC will be latched off immediately.
FB (feedback)
This pin is connected to the collector of the opto-
coupler. Internally, during normal operation, this pin is
connected to reference voltage source with a pull-up
resistor (RFB). The IC uses the voltage on this pin to
adjust the switching frequency within the range of
maximum and minimum frequency set by FMIN pin. If
FB voltage is higher than VFBH for a certain fixed
blanking time, an extended timer will be started. If over
load/open loop protection exists longer than the
extended blanking time, IC will enter auto-restart mode.
An off timer starts from the instant IC stops switching till
IC starts another soft start. This off time is determined
by the resistors and capacitor connected to VINS pin.
CS 2
FB 3
VINS
4
VINS (mains input voltage sense)
The mains input voltage is fed to this pin via a resistive
7 HG voltage divider. If the voltage on VINS pin is higher than
the threshold VINSON, IC will start to operate with
softstart when VCC increases beyond turn on
threshold. During operation, if the voltage on this pin
6
LG
falls below the threshold VINSON, IC will stop switching
until the voltage on this pin increases again.
When IC goes into over load protection mode, IC will
stop switching and try to restart after a period of time.
This period can be adjusted by connecting different
5 GND capacitors between this pin and ground.
Figure 1 Pin configuration with PG-DSO-8
GND (ground)
IC common ground.
LG (low side gate drive)
Low side power MOSFET driver.
1.2 Pin Functionality
HG (high-side gate drive)
Up side power MOSFET driver.
FMIN (minimum switching frequency)
An external resistor is connected between this pin and
the ground. The voltage of this pin is constant during
operation and thus the resistance determines the
current flowing out of this pin. The minimum switching
frequency is determined by this current. The maximum
VCC (IC power supply)
Supply voltage of the IC.
Version 2.0
5 02 July 2011
5 Page 
Half-Bridge Resonant Controller
ICE1HS01G-1
voltage. The charging time tcha and discharging time
tdisc can be respectively approximated as
tcha
=
–
ln
æ
ç
ç
ç
è
èæ-èæ--VV-----BB---UU---SS----××---R-R-------R-R-----II----N-N--e-e-----q-S-qS-------1--1-øö-øö----++-----((--II--I-I-NN---SS---TT----××---RR----ee--qq--)-)---––----V-V----II--NN---SS--H-L-ø÷÷÷ö
×
Req
×
CINS
[8]
tdisc
=
–
ln
æ
ç
ç
ç
è
V-V----BB---UU---SS----××---R-R-----RR--------I-I---eNe-N-----q-q---S-S--2-2----1--1---–-–----VV----I-I-NN---SS---HL-ø÷÷÷ö
× Req2 × CINS
[9]
In [8], Req is the equivalent resistance for paralleling of
RINS1 and RINS2.
1
Req = ------1--------------------1-------
R-----I-N----S---1 + R-----I-N----S--2-
[10]
In [9], Req2 is the equivalent resistance for paralleling of
RINS1, RINS2 and RQ3 (900ohm typically).
1
Req2 = -R---------I--1-N-------S----1-----+-----R---------I--1-N-------S-----2----+-----R-------1--Q-------3
[11]
IC will repeat the charging and discharging process for
NOLP_R times. After that, IC will turn off the switches for
both charging and discharging. In addition, the current
source for hysteresis will be turned on and another
blanking time of TBL_VINS, the time between t2 and t3 as
shown in Figure 14, will be added so that VINS pin fully
recovers and represents the bus voltage information.
IC will start the soft start after the additional blanking
time in case VVINS is higher than the VVINSon.
Vdd
IINST
Q1
ICE1HS01G
VINS
Q2
CV1
Ihys 1.25V
Mains_OK
VINS_H
VINS_L
t1 t2 t3 Time
Figure 14 VINS voltage waveform during blanking
time after OLP and before IC restarts
4.5V
CV2
EnA
Q3
CV3
EnA
0.5V
RQ
SQ
Counter
CLK
TBL_VINS
20ms
AR_R
AR
Figure 13 Circuit connected to VINS pin
Version 2.0
11 02 July 2011
11 Page | ||
| Páginas | Total 19 Páginas | |
| PDF Descargar | [ Datasheet ICE1HS01G-1.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| ICE1HS01G-1 | Half-Bridge Resonant Controller | Infineon |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |