DataSheet.es    


PDF 93C56A Data sheet ( Hoja de datos )

Número de pieza 93C56A
Descripción 3-Wire Serial EEPROM
Fabricantes FMD 
Logotipo FMD Logotipo



Hay una vista previa y un enlace de descarga de 93C56A (archivo pdf) en la parte inferior de esta página.


Total 23 Páginas

No Preview Available ! 93C56A Hoja de datos, Descripción, Manual

Fremont Micro Devices
3-Wire Serial EEPROM
1K, 2K and 4Kbit (8-bit or 16-bit wide)
93C46/A, 93C56/A, 93C66/A
FEATURES
Standard Voltage and Low Voltage Operation:
FT93C46/56/66:
VCC = 2.5V to 5.5V
FT93C46A/56A/66A:
VCC = 1.8V to 5.5V
User Selectable Internal Organization:
FT93C46: 128 x 8 or 64 x 16
FT93C56: 256 x 8 or 128 x 16
FT93C66: 512 x 8 or 256 x 16
2 MHz Clock Rate (5V) Compatibility.
Industry Standard 3-wire Serial Interface.
Self-Timed ERASE/WRITE Cycles (5ms max including auto-erase).
Automatic ERAL before WRAL.
Sequential READ Function.
High Reliability: Typical 1 Million Erase/Write Cycle Endurance.
100 Years Data Retention.
Industrial Temperature Range (-40o C to 85o C).
Standard 8-pin PDIP/SOIC/TSSOP Pb-free Packages.
DESCRIPTION
The FT93C46/56/66 series are 1024/2048/4096 bits of serial Electrical Erasable and Programmable
Read Only Memory, commonly known as EEPROM. They are organized as 64/128/256 words of 16 bits
each when the ORG pin is connected to VCC (or unconnected) and 128/256/512 words of 8 bits (1 byte)
each when the ORG pin is tied to ground. The devices are fabricated with proprietary advanced CMOS
process for low power and low voltage applications. These devices are available in standard 8-lead
PDIP, 8-lead JEDEC SOIC and 8-lead TSSOP packages. Our extended VCC range (1.8V to 5.5V)
devices enables wide spectrum of applications.
The FT93C46/56/66 is enabled through the Chip Select pin (CS), and accessed via a 3-wire serial
interface consisting of Data Input (DI), Data Output (DO), and Shift Clock (SCL). Upon receiving a READ
instruction at DI, the address is decoded and the data is clocked out serially on the data output pin DO.
The WRITE cycle is completely self-timed and no separate ERASE cycle is required before WRITE. The
WRITE cycle is only enabled when the part is in the ERASE/WRITE ENABLE state. Once a device
begins its self-timed program procedure, the data out pin (DO) can indicate the READY/BUSY status by
rising chip select (CS).
© 2013 Fremont Micro Devices Inc.
Confidential Rev. 0.8
DS93CXX-A-page1

1 page




93C56A pdf
Fremont Micro Devices
93C46/A, 93C56/A, 93C66/A
INSTRUCTION SETS DESCRIPTION
(A) READ
The Read (READ) instruction contains the Address code for the memory location to be read. After the
instruction and address are decoded, data from the selected memory location is available at the serial
output pin DO. Output data changes are synchronized with the rising edges of serial clock SK. It
should be noted that when a dummy bit (logic “0”) precedes the 8- or 16-bit data output string.
(B) ERASE/WRITE ENABLE
To assure data integrity, the part automatically goes into the Erase/Write Disable (EWDS) state when
power is first applied. An Erase/Write Enable (EWEN) instruction must be executed first before any
programming instructions can be carried out. Please note that once in the Erase/Write Enable state,
programming remains enabled until an Erase/Write Disable (EWDS) instruction is executed or VCC
power is removed from the part.
(C) ERASE/WRITE DISABLE
To protect against accidental data disturb, the Erase/Write Disable (EWDS) instruction disables all
programming modes and should be executed after all programming operations. The operation of the
READ instruction is independent of both the EWEN and EWDS instructions and can be executed at
any time.
(D) ERASE
The Erase (ERASE) instruction programs all bits in the specified memory location to the logical “1”
state. The self-timed erase cycle starts once the ERASE instruction and address are decoded. The
DO pin outputs the READY/BUSY status of the part if CS is brought high after being kept low for a
minimum of 250 ns (tCS). A logic “1” at pin DO indicates that the selected memory location has been
erased, and the part is ready for another instruction.
(E) WRITE
The Write (WRITE) instruction contains the 8 or 16 bits of data to be written into the specified memory
location. The self-timed programming cycle, tWP, starts after the last bit of data is received at serial
data input pin DI. The DO pin outputs the READY/BUSY status of the part if CS is brought high after
being kept low for a minimum of 250 ns (tCS). A logic “0” at DO indicates that programming is still in
progress. A logic “1” indicates that the memory location at the specified address has been written with
the data pattern contained in the instruction and the part is ready for further instructions. A
READY/BUSY status cannot be obtained if the CS is brought high after the end of the self-timed
programming cycle, tWP.
(F) ERASE ALL
The Erase All (ERAL) instruction programs every bit in the memory array to the logic “1” state and is
primarily used for testing purposes. The DO pin outputs the READY/BUSY status of the part if CS is
brought high after being kept low for a minimum of 250 ns (tCS). The ERAL instruction is valid only at
VCC = 5.0V ± 10%.
(G) WRITE ALL
The Write All (WRAL) instruction programs all memory locations with the data patterns specified in the
instruction. The DO pin outputs the READY/BUSY status of the part if CS is brought high after being
kept low for a minimum of 250 ns (tCS). The WRAL instruction is valid only at VCC = 5.0V ± 10%.
© 2013 Fremont Micro Devices Inc.
Confidential Rev. 0.8
DS93CXX-A-page5

5 Page





93C56A arduino
Fremont Micro Devices
ORDER CODE:
Circuit Type
FT93C46 X - X X X - X
Pin and Voltage
Blank: 2.5V-5.5V
A: 1.8V - 5.5V
R: Pin Rotated and 2.5-5.5V
RA: Pin Rotated and 1.8-5.5V
Temp. Range
C: 0-70
I: -40-85
U: -40-85
93C46/A, 93C56/A, 93C66/A
Packaging
B: Tube
T: Tape and Reel
HSF
R: RoHS
G: RoHS and Halogen Free
Package
D: DIP8
S: SOP8
T: TSSOP8
Density
56: 2kbits
66: 4kbits
Pin and Voltage
Blank: 2.5V-5.5V
A: 1.8V-5.5V
Temp. Range
C: 0-70
I: -40-85
U: -40-85
FT93Cxx X - X X X - X
Packaging
B: Tube
T: Tape and Reel
HSF
R: RoHS
G: RoHS and Halogen Free
Package
D: DIP8
S: SOP8
T: TSSOP8
© 2013 Fremont Micro Devices Inc.
Confidential Rev. 0.8
DS93CXX-A-page11

11 Page







PáginasTotal 23 Páginas
PDF Descargar[ Datasheet 93C56A.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
93C563-Wire Serial EEPROMsATMEL Corporation
ATMEL Corporation
93C5616Kbit/ 8Kbit/ 4Kbit/ 2Kbit/ 1Kbit and 256bit 8-bit or 16-bit wideSTMicroelectronics
STMicroelectronics
93C56Electrically Erasable Programmable MemoriesNational Semiconductor
National Semiconductor
93C562K 5.0V Automotive Temperature Microwire Serial EEPROMMicrochip Technology
Microchip Technology

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar