DataSheet.es    


PDF 74HCT123-Q100 Data sheet ( Hoja de datos )

Número de pieza 74HCT123-Q100
Descripción Dual retriggerable monostable multivibrator
Fabricantes NXP Semiconductors 
Logotipo NXP Semiconductors Logotipo



Hay una vista previa y un enlace de descarga de 74HCT123-Q100 (archivo pdf) en la parte inferior de esta página.


Total 23 Páginas

No Preview Available ! 74HCT123-Q100 Hoja de datos, Descripción, Manual

74HC123-Q100; 74HCT123-Q100
Dual retriggerable monostable multivibrator with reset
Rev. 2 — 19 January 2015
Product data sheet
1. General description
The 74HC123-Q100; 74HCT123-Q100 are high-speed Si-gate CMOS devices and are pin
compatible with Low-power Schottky TTL (LSTTL). They are specified in compliance with
JEDEC standard no. 7A.
The 74HC123-Q100; 74HCT123-Q100 are dual retriggerable monostable multivibrators
with output pulse width control by three methods:
1. The basic pulse is defined by the selection of the external resistor (REXT) and
capacitor (CEXT).
2. Once triggered, the basic output pulse width may be extended by retriggering the
gated active LOW-going edge input (nA) or the active HIGH-going edge input (nB). By
repeating this process, the output pulse period (nQ = HIGH, nQ = LOW) can be made
as long as desired. Alternatively an output delay can be terminated at any time by a
LOW-going edge on input nRD, which also inhibits the triggering.
3. An internal connection from nRD to the input gates makes it possible to trigger the
circuit by a HIGH-going signal at input nRD as shown in Table 3.
Schmitt trigger action in the nA and nB inputs, makes the circuit highly tolerant to slower
input rise and fall times.
This product has been qualified to the Automotive Electronics Council (AEC) standard
Q100 (Grade 1) and is suitable for use in automotive applications.
2. Features and benefits
Automotive product qualification in accordance with AEC-Q100 (Grade 1)
Specified from 40 C to +85 C and from 40 C to +125 C
DC triggered from active HIGH or active LOW inputs
Retriggerable for very long pulses up to 100 % duty factor
Direct reset terminates output pulse
Schmitt trigger action on all inputs except for the reset input
ESD protection:
MIL-STD-883, method 3015 exceeds 2000 V
HBM JESD22-A114F exceeds 2000 V
MM JESD22-A115-A exceeds 200 V (C = 200 pf, R = 0 )
Specified from 40 C to +85 C and from 40 C to +125 C

1 page




74HCT123-Q100 pdf
NXP Semiconductors
74HC123-Q100; 74HCT123-Q100
Dual retriggerable monostable multivibrator with reset
6. Functional description
Table 3.
Input
nRD
L
X
X
H
Function table[1]
nA
X
H
X
L
H
L
nB
X
X
L
H
H
Output
nQ
L
L[2]
L[2]
nQ
H
H[2]
H[2]
[1] H = HIGH voltage level; L = LOW voltage level; X = don’t care; = LOW-to-HIGH transition; = HIGH-to-LOW transition;
= one HIGH level output pulse;
= one LOW level output pulse.
[2] If the monostable was triggered before this condition was established, the pulse continues as programmed.
7. Limiting values
Table 4. Limiting values
In accordance with the Absolute Maximum Rating System (IEC 60134). Voltages are referenced to GND (ground = 0 V).
Symbol Parameter
Conditions
Min Max Unit
VCC supply voltage
IIK input clamping current
VI < 0.5 V or VI > VCC + 0.5 V
0.5 +7
- 20
V
mA
IOK output clamping current
IO output current
VO < 0.5 V or VO > VCC + 0.5 V
except for pins nREXT/CEXT;
VO = 0.5 V to (VCC + 0.5 V)
- 20 mA
- 25 mA
ICC
IGND
Tstg
supply current
ground current
storage temperature
- 50 mA
- 50 mA
65 +150 C
Ptot total power dissipation
SO16 package
[1] -
500 mW
TSSOP16 package
[2] -
500 mW
DHVQFN16 package
[3] -
500 mW
[1] For SO16 packages: Ptot derates linearly with 8 mW/K above 70 C.
[2] For TSSOP16 packages: Ptot derates linearly with 5.5 mW/K above 60 C.
[3] For DHVQFN16 packages: Ptot derates linearly with 4.5 mW/K above 60 C.
74HC_HCT123_Q100
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 January 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
5 of 23

5 Page





74HCT123-Q100 arduino
NXP Semiconductors
74HC123-Q100; 74HCT123-Q100
Dual retriggerable monostable multivibrator with reset

W:
QV




DDD





. IDFWRU



DDD


   
&(;7 S)


9&& 9
VCC = 5.0 V; Tamb = 25 C.
(1) REXT = 100 k
(2) REXT = 50 k
(3) REXT = 10 k
(4) REXT = 2 k
Fig 7. Typical output pulse width as a function of the
external capacitor value
CEXT = 10 nF; REXT = 10 kto 100 k.
Tamb = 25 C.
Fig 8. 74HC123-Q100 typical ‘K’ factor as function of
VCC
74HC_HCT123_Q100
Product data sheet
All information provided in this document is subject to legal disclaimers.
Rev. 2 — 19 January 2015
© NXP Semiconductors N.V. 2015. All rights reserved.
11 of 23

11 Page







PáginasTotal 23 Páginas
PDF Descargar[ Datasheet 74HCT123-Q100.PDF ]




Hoja de datos destacado

Número de piezaDescripciónFabricantes
74HCT123-Q100Dual retriggerable monostable multivibratorNXP Semiconductors
NXP Semiconductors

Número de piezaDescripciónFabricantes
SLA6805M

High Voltage 3 phase Motor Driver IC.

Sanken
Sanken
SDC1742

12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters.

Analog Devices
Analog Devices


DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares,
permitiéndote verlos en linea o descargarlos en PDF.


DataSheet.es    |   2020   |  Privacy Policy  |  Contacto  |  Buscar