|
|
PDF GS8320Z36GT-V Data sheet ( Hoja de datos )
| Número de pieza | GS8320Z36GT-V | |
| Descripción | 36Mb Pipelined and Flow Through Synchronous NBT SRAMs | |
| Fabricantes | GSI Technology | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de GS8320Z36GT-V (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
|
No Preview Available !
Preliminary
GS8320Z18/36T-xxxV
100-Pin TQFP
Commercial Temp
Industrial Temp
36Mb Pipelined and Flow Through
Synchronous NBT SRAMs
250 MHz–133 MHz
1.8 V or 2.5 V VDD
1.8 V or 2.5 V I/O
Features
• NBT (No Bus Turn Around) functionality allows zero wait
read-write-read bus utilization; Fully pin-compatible with
both pipelined and flow through NtRAM™, NoBL™ and
ZBT™ SRAMs
• 1.8 V or 2.5 V core power supply
• 1.8 V or 2.5 V I/O supply
• User-configurable Pipeline and Flow Through mode
• LBO pin for Linear or Interleave Burst mode
• Pin compatible with 2Mb, 4Mb, 8Mb, and 16Mb devices
• Byte write operation (9-bit Bytes)
• 3 chip enable signals for easy depth expansion
• ZZ Pin for automatic power-down
• JEDEC-standard 100-lead TQFP package
• RoHS-compliant 100-lead TQFP package available
Functional Description
The GS8320Z18/36T-xxxV is a 36Mbit Synchronous Static
SRAM. GSI's NBT SRAMs, like ZBT, NtRAM, NoBL or
other pipelined read/double late write or flow through read/
single late write SRAMs, allow utilization of all available bus
bandwidth by eliminating the need to insert deselect cycles
when the device is switched from read to write cycles.
Because it is a synchronous device, address, data inputs, and
read/ write control inputs are captured on the rising edge of the
input clock. Burst order control (LBO) must be tied to a power
rail for proper operation. Asynchronous inputs include the
Sleep mode enable (ZZ) and Output Enable. Output Enable can
be used to override the synchronous control of the output
drivers and turn the RAM's output drivers off at any time.
Write cycles are internally self-timed and initiated by the rising
edge of the clock input. This feature eliminates complex off-
chip write pulse generation required by asynchronous SRAMs
and simplifies input signal timing.
The GS8320Z18/36T-xxxV may be configured by the user to
operate in Pipeline or Flow Through mode. Operating as a
pipelined synchronous device, meaning that in addition to the
rising edge triggered registers that capture input signals, the
device incorporates a rising-edge-triggered output register. For
read cycles, pipelined SRAM output data is temporarily stored
by the edge triggered output register during the access cycle
and then released to the output drivers at the next rising edge of
clock.
The GS8320Z18/36T-xxxV is implemented with GSI's high
performance CMOS technology and is available in a JEDEC-
standard 100-pin TQFP package.
Parameter Synopsis
-250 -225 -200 -166 -150 -133 Unit
Pipeline
tKQ
tCycle
3.0 3.0 3.0 3.5 3.8 4.0 ns
4.0 4.4 5.0 6.0 6.6 7.5 ns
3-1-1-1 Curr (x18) 285 265 245 220 210 185 mA
Curr (x32/x36) 350 320 295 260 240 215 mA
Flow
Through
2-1-1-1
tKQ
tCycle
Curr (x18)
Curr (x32/x36)
6.5
6.5
205
235
7.0
7.0
195
225
7.5
7.5
185
210
8.0
8.0
175
200
8.5
8.5
165
190
8.5
8.5
155
175
ns
ns
mA
mA
Rev: 1.02 5/2006
1/23
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
1 page  
Preliminary
GS8320Z18/36T-xxxV
GS8320Z18/36T-xxxV NBT SRAM Functional Block Diagram
Rev: 1.02 5/2006
5/23
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
5 Page 
Preliminary
GS8320Z18/36T-xxxV
Burst Cycles
Although NBT RAMs are designed to sustain 100% bus bandwidth by eliminating turnaround cycle when there is transition from
read to write, multiple back-to-back reads or writes may also be performed. NBT SRAMs provide an on-chip burst address
generator that can be utilized, if desired, to further simplify burst read or write implementations. The ADV control pin, when
driven high, commands the SRAM to advance the internal address counter and use the counter generated address to read or write
the SRAM. The starting address for the first cycle in a burst cycle series is loaded into the SRAM by driving the ADV pin low, into
Load mode.
Burst Order
The burst address counter wraps around to its initial state after four addresses (the loaded address and three more) have been
accessed. The burst sequence is determined by the state of the Linear Burst Order pin (LBO). When this pin is low, a linear burst
sequence is selected. When the RAM is installed with the LBO pin tied high, Interleaved burst sequence is selected. See the tables
below for details.
Mode Pin Functions
Mode Name
Pin Name State
Function
Burst Order Control
L
LBO H
Linear Burst
Interleaved Burst
Output Register Control
FT
L
H or NC
Flow Through
Pipeline
Power Down Control
L or NC
ZZ H
Active
Standby, IDD = ISB
Note:
There is a pull-up device on the FT pin and a pull-down device on the ZZ pin, so this input pin can be unconnected and the chip will operate in
the default states as specified in the above table.
Burst Counter Sequences
Linear Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0]
1st address 00 01 10 11
2nd address 01 10 11 00
3rd address 10 11 00 01
4th address 11 00 01 10
Note:
The burst counter wraps to initial state on the 5th clock.
Interleaved Burst Sequence
A[1:0] A[1:0] A[1:0] A[1:0]
1st address 00 01 10 11
2nd address 01 00 11 10
3rd address 10 11 00 01
4th address 11 10 01 00
Note:
The burst counter wraps to initial state on the 5th clock.
BPR 1999.05.18
Rev: 1.02 5/2006
11/23
Specifications cited are subject to change without notice. For latest documentation see http://www.gsitechnology.com.
© 2001, GSI Technology
11 Page | ||
| Páginas | Total 23 Páginas | |
| PDF Descargar | [ Datasheet GS8320Z36GT-V.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| GS8320Z36GT-V | 36Mb Pipelined and Flow Through Synchronous NBT SRAMs | GSI Technology |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |