|
|
PDF DM13H-E Data sheet ( Hoja de datos )
| Número de pieza | DM13H-E | |
| Descripción | 16-Channel Constant Current LED Driver | |
| Fabricantes | SiTi | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de DM13H-E (archivo pdf) en la parte inferior de esta página. Total 25 Páginas | ||
|
No Preview Available !
DM13H-E
Version
Issue Date
File Name
Total Pages
: A.004
: 2015/06/25
: SP-DM13H-E A.004.doc
: 25
16-Channel Constant Current LED Driver
with Error Detection
新竹市科學園區展業一路 9 號 4 樓之 3
SILICON TOUCH TECHNOLOGY INC.
9-4F-3, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Tel：886-3-5645656 Fax：886-3-5645626
1 page  
Equivalent Circuit of Inputs and Outputs
1.CLK, DAI, LAT , EN terminals ( Schmitt Trigger Input )
DM13H-E
2. DAO terminals
16-bit Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 4
5 Page 
DM13H-E
Serial Data Interface
DM13H-E includes a flexible data transfer interface. The data can be transferred from
DAI pin to the shift registers at the rising edge of CLK. After all data are clocked in, a rising
edge of the LAT signal can transfer the serial data to the data latches (Edge trigger). The
serial data format can be 16-bit or 10-bit wide, depending on the operating mode of the
device.
Operation Mode
DM13H-E has two operating modes depending on the combination of CLK and LAT
signals. The table below shows the available operating modes. For normal operation (SD
mode), the data width of shift register is 16-bit, which is used to set 16 bits serial-in image
data. The sequence of the combination of CLK and LAT explains in following pages is
used to change the operation mode. If there are four triggering clock pulses (CLK) with high
level latch (LAT ), DM13H-E will change to command data input mode (CD mode) at falling
edge of the latch pulse (LAT ) then user can make ten triggering clock pulses to set 1-bit
voltage level selection of short detection (default value after power-on is 1’b1).
OPERATION MODE
Serial-in Data Input Mode (SD mode)
Command Data Input Mode (CD mode)
SHIFT REGISTER
16-bit
10-bit
16-bit Constant Current LED Driver with Error Detection
Version:A.004
未經授權而逕予重製、複製、使用或公開本文件，行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 10
11 Page | ||
| Páginas | Total 25 Páginas | |
| PDF Descargar | [ Datasheet DM13H-E.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| DM13H-E | 16-Channel Constant Current LED Driver | SiTi |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |