|
|
Número de pieza | DM11H | |
Descripción | 8-Channel Constant Current LED Driver | |
Fabricantes | SiTi | |
Logotipo | ||
Hay una vista previa y un enlace de descarga de DM11H (archivo pdf) en la parte inferior de esta página. Total 23 Páginas | ||
No Preview Available ! DM11H
Version
Issue Date
File Name
Total Pages
: PRE.002
: 2009/10/13
: SP-DM11H-PRE.002.doc
: 23
8-Channel Constant Current LED Driver
with Error Detection
新竹市科學園區展業一路 9 號 7 樓之 1
SILICON TOUCH TECHNOLOGY INC.
9-7F-1, Prosperity Road I, Science Based Industrial Park,
Hsin-Chu, Taiwan 300, R.O.C.
Tel:886-3-5645656 Fax:886-3-5645626
1 page Equivalent Circuit of Inputs and Outputs
1.CLK, DAI, LAT , EN terminals ( Schmitt Trigger Input )
DM11H
2. DAO terminals
8-bit Constant Current LED Driver with Error Detection
Version:PRE.002
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 4
5 Page DM11H
Serial Data Interface
DM11H includes a flexible data transfer interface. The data can be transferred from DAI
pin to the shift registers at the rising edge of CLK. After all data are clocked in, a rising edge
of the LAT signal can transfer the serial data to the data latches (Edge trigger). The serial
data format can be 8-bit or 10-bit wide, depending on the operating mode of the device.
Operation Mode
DM11H has two operating modes depending on the combination of CLK and LAT
signals. The table below shows the available operating modes. For normal operation (SD
mode), the data width of shift register is 8-bit, which is used to set 8 bits serial-in image data.
The sequence of the combination of CLK and LAT explains in following pages is used to
change the operation mode. If there are four triggering clock pulses (CLK) with high level
latch (LAT ), DM11H will change to command data input mode (CD mode) at falling edge of
the latch pulse (LAT ) then user can make ten triggering clock pulses to set 7-bit GBC data
(default value after power-on is 7’b1000000), 2-bit voltage level selection of short detection
(default value after power-on is 1’b10) and 1-bit sleep control data (default value is 1’b0)
OPERATION MODE
Serial-in Data Input Mode (SD mode)
Command Data Input Mode (CD mode)
SHIFT REGISTER
8-bit
10-bit
8-bit Constant Current LED Driver with Error Detection
Version:PRE.002
未經授權而逕予重製、複製、使用或公開本文件,行為人得被追究侵權之相關民刑事責任
Unauthorized reproduction, duplication, use or disclosure of this document will be deemed as infringement.
Page 10
11 Page |
Páginas | Total 23 Páginas | |
PDF Descargar | [ Datasheet DM11H.PDF ] |
Número de pieza | Descripción | Fabricantes |
DM114 | (DM115) 8-Bit Constant Current LED Drivers | SiTi |
DM115 | (DM114) 8-Bit Constant Current LED Drivers | SiTi |
DM117 | 8-bit Constant Current LED Driver | SiTi |
DM11H | 8-Channel Constant Current LED Driver | SiTi |
Número de pieza | Descripción | Fabricantes |
SLA6805M | High Voltage 3 phase Motor Driver IC. |
Sanken |
SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
Analog Devices |
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |