|
|
PDF CHM1290REF Data sheet ( Hoja de datos )
| Número de pieza | CHM1290REF | |
| Descripción | 20-30GHz SUB-HARMONICALLY PUMPED MIXER | |
| Fabricantes | United Monolithic Semiconductors | |
| Logotipo |  |
|
Hay una vista previa y un enlace de descarga de CHM1290REF (archivo pdf) en la parte inferior de esta página. Total 8 Páginas | ||
|
No Preview Available !
CHM1290REF
20-30GHz SUB-HARMONICALLY PUMPED MIXER
GaAs Monolithic Microwave IC in SMD leadless package
Description
The monolithic microwave IC (MMIC) in the
package is a multi-function chip which
integrates a self biased LO buffer amplifier
and a sub-harmonic diode mixer for 2LO
suppression. It is usable both for up- and
down-conversion and it is designed for a
wide range of applications, typically
commercial communication systems for
broadband local access (LMDS).
The circuit is manufactured with a PM-
HEMT process, 0.25µm gate length, via
holes through the substrate, air bridges and
electron beam gate lithography. It is
supplied in a new SMD-type leadless chip
carrier.
SMD Package Dimensions
Main Features
• Broadband performance : 20-30GHz
• 10.5 dB conversion Loss
• -25dBm 2LO Power @ RF port
• -4dBm LO input power
• -3dBm input power 1dB compression
• Low DC power consumption,
33mA@ 3.0V
• Dimensions: 5.08 x 5.08 x 0.97 mm3
Ref.: DSCCHM1290REF2239 -27-Aug.-02 1/6 Specifications subject to change without notice
Route Départementale 128 , B.P.46 - 91401 ORSAY Cedex - FRANCE
Tel.: +33 (0)1 69 33 03 08 - Fax : +33 (0)1 69 33 03 09
1 page  
20-30GHz SHP Mixer
Application note
CHM1290REF
The design of the motherboard has a strong impact on the over all performance since
the transition from the motherboard to the package is comparably large. In case of
the SMD-type packages of United Monolithic Semiconductors the motherboard
should be designed according to the information given in the following to achieve
good performance. Other configurations are also possible but can lead to different
results. If you need advise please contact United Monolithic Semiconductors for
further information.
SMD-type packages of UMS should allow design and fabrication of micro- and mm-
wave modules at low cost. Therefore, a suitable motherboard environment has been
chosen. All tests and verifications have been performed on Rogers RO4003. This
material exhibits a permittivity of 3.38 and has been used with a thickness of 200µm
[8 mils] and a 1/2oz or less copper cladding. The corresponding 50 Ohm
transmission line has a strip width of about 460µm [approx. 18 mils].
The contact areas on the motherboard for the package connections should be
designed according to the footprint given above. The proper via structure under the
ground pad is very important in order to achieve a good RF and lifetime performance.
All tests have been done by using a grid of plenty plated through vias with a diameter
of less than 200µm [8 mils] and a spacing of less than 400µm [16 mils] from the
centres of two adjacent vias. The via grid should cover the whole space under the
ground pad and the vias closest to the RF ports should be located near the edge of
the pad to allow a good RF ground connection. Since the vias are important for heat
transfer, a proper via filling should be guaranteed during the mounting procedure to
get a low thermal resistance between package and heat sink. For power devices the
use of heat slugs in the motherboard instead of a via grid is recommended.
For the mounting process the SMD-type package can be handled as a standard
surface mount component. The use of either solder or conductive epoxy is possible.
The solder thickness after reflow should be typical 50µm [2 mils] and the lateral
alignment between the package and the motherboard should be within 50µm [2 mils].
Caution should be taken to obtain a good and reliable contact over the whole pad
areas. Voids or other improper connections, in particular, between the ground pads of
motherboard and package will lead to a deterioration of the RF performance and the
heat dissipation. The latter effect can reduce drastically reliability and lifetime of the
product.
Ref. : DSCCHM1290REF2239 -27-Aug.-02
5/6
Specifications subject to change without notice
Route Départementale 128 , B.P.46 - 91401 ORSAY Cedex - FRANCE
Tel.: +33 (0)1 69 33 03 08 - Fax : +33 (0)1 69 33 03 09
5 Page | ||
| Páginas | Total 8 Páginas | |
| PDF Descargar | [ Datasheet CHM1290REF.PDF ] | |
Hoja de datos destacado
| Número de pieza | Descripción | Fabricantes |
| CHM1290REF | 20-30GHz SUB-HARMONICALLY PUMPED MIXER | United Monolithic Semiconductors |
| Número de pieza | Descripción | Fabricantes |
| SLA6805M | High Voltage 3 phase Motor Driver IC. |
 Sanken |
| SDC1742 | 12- and 14-Bit Hybrid Synchro / Resolver-to-Digital Converters. |
 Analog Devices |
|
DataSheet.es es una pagina web que funciona como un repositorio de manuales o hoja de datos de muchos de los productos más populares, |
| DataSheet.es | 2020 | Privacy Policy | Contacto | Buscar |